In IPv6, the interfaces running OSPF can be configured with multiple ad dress prefixes. Which statement is true about the IPv6 addresses that can be included into the OSPF process?" ()
第1题:
When implementing OSPFv3, which statement describes the configuration of OSPF areas?()
第2题:
Which three steps are used to configure IPv6 in JUNOS software?()
第3题:
Which of these commands can you use to show if an operational Catalyst switch port is set for autonegotiation of speed and duplex when running Cisco IOS software?()
第4题:
Which two are valid agent interfaces for Cisco Unified Contact Center Express?()
第5题:
Running both IPv4 and IPv6 on a router simultaneously is known as what?()
第6题:
In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3 areas.
In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3 areas.
In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to OSPFv3 areas.
In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to OSPFv3 areas.
第7题:
Macintosh workstation with Cisco IP Phone Agent
Linux workstation running CAD with IP Communicator
Linux workstation running CAD with Cisco Unified IP Phone 7960G
Citrix Terminal running CAD with IP Communicator
Citrix Terminal with Cisco IP Phone Agent
Windows workstation running CAD with Media Termination option
第8题:
Only one IPv6 address can be assigned to each interface.
IPv6 hosts use anycast addresses to assign IP addresses to interfaces.
Each host can a utoconfigure its address without the aid of a DHCP server.
Only one IPv6 address is assigned per node.
第9题:
Assign 128-bit router ID
Enable a routing instance.
Assign IPv6 addresses to interfaces.
Add IPv6 family support to interfaces
第10题:
Configure a routing process using the command ipv6 router ospf [process-id].
Add the network statement for the interfaces on which OSPF will run.
Configure OSPF on the interface that it will run on.
Use the passive-interface command on the interfaces on which OSPF should not run.
Enable routing.
第11题:
RIPng will be enabled on no interfaces.
RIPng will be enabled on one interface.
RIPng will be enabled on two interfaces.
RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.
第12题:
EIGRP for IPv6 is directly configured on the interfaces over which it runs.
EIGRP for IPv6 is not configured on the interfaces over which it runs, but if a user uses passive-interface configuration, EIGRP for IPv6 needs to be configured on the interface that is made passive.
There is a network statement configuration in EIGRP for IPv6, the same as for IPv4.
There is no network statement configuration in EIGRP for IPv6.
When a user uses a passive-interface configuration, EIGRP for IPv6 does not need to be configured on the interface that is made passive.
When a user uses a non-passive-interface configuration, EIGRP for IPv6 does not need to be configured on the interface that is made passive
第13题:
Which of the following solutions will encapsulate IPv6 packets with IPv4 headers?()
第14题:
为了查看Quidway路由器上的串口s0的封装是DTE或DCE,应该使用命令()
第15题:
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?() ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable
第16题:
Which three statements about anycast RP are true? ()
第17题:
You have just reinstalled a VIP 6-80 in a Cisco 7500 Series router. What must you do to bring up the port adapter interfaces?()
第18题:
the number of computer blades in the system
the number of interfaces sharing the uplinks
the driver version on the OS running on the computer blade
the number of uplinks between I/O Module and Fabric Interconnect
第19题:
Specific addresses can be selected using a prefix list.
Specific addresses can be selected using a route map.
Specific addresses cann ot be selected for importation into the OSPF process.
Specific addresses can be selected using an ACL.
第20题:
show port network
show controllers Ethernet-controller
第21题:
Assign 128-bit router id.
Enable a routing instance.
Assign IPv6 addresses to interfaces.
Add IPv6 family support to interfaces.
Enable IPv6-capable routing protocol.
第22题:
GRE tunnels
automatic 6 to 4 tunnels
ISATAP tunnels
manual tunnels (RFC 2893)
第23题:
Units in JUNOS are always required for any interface configured with logical addresses such as IP and IPv6.
Units in JUNOS are only required when you are configuring sub-interfaces for inter-VLAN routing.
Unit numbers must match the DLCI or VCI numbers configured on the interface.
Unit 0 is the only value allowed on interfaces running HDLC, PPP, or for Ethernet interfaces not doing VLAN-tagging.
第24题:
Create an IPv4 tunnel and assign the tunnel IPv6 addresses
Create IPv4 interfaces on both ends of the network, and use either static routes or a routingprocess to direct IPv6 packets through those interfaces
IPv6 packets cannot be encapsulated with IPv4 headers because the addresses are notcompatible
Create IFV6 interfaces on both ends of the network, and use static routes to point the IPv4address to those interfaces
Use an IPv6 routing protocol like OSPFv3 and assign IPv4 packets to that process
Create an IPv4 tunnel and use the tunnel mode ipv6ip command