You are given a PC, a router, and a cable. Select the correct combination that will allow you to log into the router locally using a terminal emulation program such as HyperTerminal.()
第1题:
A.config
B.clientqos.cnf
C.startup-config
D.running-configuration
第2题:
A.
B.
C.
D.
第3题:
You need to upgrade the IOS of an existing router on your network. The new IOS image is located on a TFTP server that you have set up within the network. What command should you issue in order to download the new IOS version?()
A. Router# copy tftp flash
B. Router# copy flash run
C. Router(config)# restore flash
D. Router(config)# repair flash
E. Router#copy flash tftp
F. Router# copy start flash
第4题:
You need to upgrade the IOS of an existing router on your network. The new IOS image is located on a TFTP server that you have set up within the network. What command should you issue in order to download the new IOS version?()
第5题:
You work as a technician at TestKing. You are configuring a Cisco router. You want to configure the IP address on an interface.Which command should you use?()
第6题:
Which command prompt indicates that you are in operational mode?()
第7题:
Which Cisco SDM feature allows you to specify whether you want SDM files installed on your PC or on your router?()
第8题:
en standby preempt
standby preempt enable
standby preempt
hot standby preempt
第9题:
config
clientqos.cnf
startup-config
running-configuration
第10题:
proceed
exceed
succeed
precede
第11题:
user@router&
user@router#
user@router%
user@router>
第12题:
ROM Monitor mode
SETUP mode
Autoflash mode
RXBOOT mode
None of the above
第13题:
After connecting a PC to an available port on a switch, you find that the PC can not access any of the resources on the LAN. No other PC's connected to the switch appear to be having any issues. What is the most likely cause for this problem?
A.The router lacks a routing table entry for the new host
B.The host switch port is assigned to the incorrect VLAN
C.The host MAC address is incorrectly configured
D.A STP instance for the new host has not been initialized
E.The switch does not have the MAC address hard coded in the CAM table.
第14题:
While troubleshooting a network connectivity issue, you suspect that a router may be missing a route, or may be receiving bad routing information to a destination. What command should you issue to view the route that the router will use to reach a given destination?()
A. ping
B. trace
C. show ip route
D. show interface
E. show cdp neighbors
第15题:
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails. What command would you use if you wanted to configure this? ()
第16题:
You have just purchased a brand new router and wish to have the router prompt you through the initial configuration commands. Which router mode does this describe?()
第17题:
Router R1 needs to be configured to advertise a specific network. Which of the followingcommands would you use if you wanted to advertise the subnet 154.2.1.0 255.255.255.0 to the EBGP neighbors on your subnet?()
第18题:
You just purchased a refurbished router that contains a configuration from a previous deployment. What should you do, before entering a new configuration into the router?()
第19题:
While troubleshooting a network connectivity issue, you suspect that a router may be missing a route, or may be receiving bad routing information to a destination. What command should you issue to view the route that the router will use to reach a given destination?()
第20题:
ping
trace
show ip route
show interface
show cdp neighbors
第21题:
RAM should be erased and the router restarted.
Flash should be erased and the router restarted.
NVRAM should be erased and the router restarted.
The new configuration should be entered and saved.
第22题:
user@router# show system services
user@router> show configuration services
user@router# show configuration system services
user@router# show system login
第23题:
Install Shield Wizard
Cisco SDM Express Wizard
Cisco SDM Image Manager
Create Connection Wizard