Access Point R1 is an Aironet 1200 that has been converted from autonomous mode to LWAPP mode. After this conversion, which two statements are true? ()
第1题:
You need to set up a Company AP to act as a wireless repeater. What are three characteristics of this wireless repeater topology?()
第2题:
Which of the following statements explains why it is normally best to have more than one controller-basedaccess point participate in the containment of one rogue access point?()
第3题:
A default Frame Relay WAN is classified as what type of physical network?()
第4题:
On a Cisco Aironet 1130AG Series standalone access point, the status LED is dark blue and blinking. What does this indicate?()
第5题:
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However, when it is powered up, the access point fails. What has caused this problem?()
第6题:
You are installing a cisco aironet 1000 series controller-based access point. when you boot it, all the leds on the access point blink together. What does this indicate about the access point?()
第7题:
Which two statements about a wireless repeater topology are true?()
第8题:
Control traffic between an access point and a controller is encrypted within LWAPP.
Data traffic between an access point and a controller is encrypted within LWAPP.
Layer 3 mode packets are transmitted in TCP frames.
Data traffic between an access point and a controller is encapsulated within LWAPP.
VLAN tagging and QoS markings are applied at the access point.
第9题:
Choose Configure >Access_Point, then enter the AP MAC address
Choose Configure >Access_Point, then enter the IP address of the AP
Wait until the WLC downloads its code from the WCS and choose the access point from the list under the WLC option of the Configure menu
Wait until the AP downloads its code from the WCS and choose the access point from the list under the Access_Point option of the Configure menu
第10题:
An access point will search for a controller using a broadcast address if using LWAPP Layer 2 and a unicast address if using LWAPP Layer 3 mode.
If multiple wireless controllers are detected by an access point, the controller with the fewest associated access points is chosen to associate with.
In order to associate in Layer 3 mode, the access point must have been preconfigured with an IP address.
Once an access point associates with a controller in LWAPP Layer 3 mode, it receives an IP address from the controller.
An access point first searches for a controller in LWAPP Layer 2 mode. If the search is not successful, the access point then attempts to locate a controller in LWAPP Layer 3 mode.
If multiple wireless controllers are detected by an access point, all of them will be used and traffic will be load balanced.
第11题:
clients connected to the rogue access point must be able to connect to the containment controller-based access point.
multiple controller-based access points will load-balance the containment task using fewer resources than a single access point.
clients connected to the rogue access point may be out of the range of the controller-based access point providing containment.
each controller-based access point can handle only a limited amount of clients connected to the rogue access points.
第12题:
1. Access point sends probe request .2. Client sends probe response.3. Client initiates association.4. Access point accepts association.5. Client adds access point MAC address to association table.
1. Client sends probe request.2. Access point sends probe response.3. Client initiates association.4. Access point accepts association.5. Access point adds client MAC address to association table.
1. Client sends probe request.2. Access point sends probe response.3. Access point initiates association.4. Client accepts association.5. Access point adds client MAC address to association table.
1. Access point sends probe request .2. Client sends probe response.3. Client initiates association.4. Access point accepts association.5. Access point adds client MAC address to association table.
1. Client sends probe request.2. Access point sends probe response.3. Client initiates association.4. Access point accepts association.5. Client adds access point MAC address to association table.
None of the other alternatives apply.
第13题:
The LWAPP (Lightweight Access Point Protocol) is in use within the Company wireless LAN. Which statement is true about this protocol?()
第14题:
In the Company wireless LAN, what is the function of the Service Set Identifier (SSID)?()
第15题:
Which is NOT part of a typical wireless site survey?()
第16题:
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24PWR Switch. However, when it is powered up, the access point fails. What has caused this problem?()
第17题:
The Lightweight Access Point Protocol (LWAPP) is in use within the Company wireless network. Which two statements correctly describe features of this protocol? ()
第18题:
On a Cisco Aironet 1130 Series autonomous access point, the status indicator is blinking dark blue. What does this indicate?()
第19题:
The SSID must match on both the Company client and the Company access point and provides MAC Address Authentication to authenticate the client to the access point.
The SSID should be configured on the Company client site only and provides data-privacy functions and authentication to the access point.
The SSID must match on both the Company client and the Company access point and provides encryption keys for authentication to the access point.
The SSID must match on both the Company client and the Company access point. The SSID is advertised in plain-text in the access point beacon messages.
None of the other alternatives apply
第20题:
LWAPP-enabled access points can still communicate with Wireless Domain Services (WDS) devices.
An LWAPP-enabled access point console port provides read-only access to the unit.
LWAPP-enabled access points support Layer 2 LWAPP.
LWAPP-enabled access points must get an IP address and discover the controller using DHCP, DNS, or an IP subnet broadcast.
An LWAPP-enabled access point console port provides read-write access to the unit.
第21题:
Real-time frame exchange is accomplished within the access point.
The control traffic between the client and the access point is encapsulated with the LWAPP.
Authentication, security, and mobility are handled by the access point.
Data traffic between the client and the access point is encapsulated with LWAPP.
None of the other alternatives apply
第22题:
A wireless repeater is an access point that is not connected to the wired LAN.
The repeater feature is only available in lightweight access point topologies.
The SSID of the root access point must be configured on the repeater access point.
This topology requires a 10 - 15 percent overlap between a wired access point and the wireless repeater.
This topology requires a 15 - 25 percent overlap between a wired access point and the wireless repeater.
To avoid interference, the repeater access point must use a different channel from what the root access point uses.
第23题:
known internal
managed
friendly
known external