Company.com has a two-node HACMP cluster with a single cascading resource group. Node ’A’ is the normal production node, and Node ’B’ is the standby node. One of the first steps in the HACMP test plan is to start the cluster and to verify that al elements for the resource group have been acquired. The administrator who is conducting the HACMP test starts the HACMP daemons on Node ’B’ with the ’smitty clstart" command. The administrator notices that Node ’B’ acquires the elements of the resource group, including a service IP labels,a shared volume group, and an application server that has been started. The expectation was that Node ’B’ would enter the cluster in a standby status, rather than acquiring production resources. What should the administrator do to correct this problem?()
第1题:
While performing a site survey to document the existing environment before implementing a new HACMP cluster, it was discovered that a port filtering firewall was being used to protect the production system. The plan is to continue using the firewall and add a second firewall to avoid a single point of failure. Each node in the two-node cluster will have all of its network adapters connected to the firewalls, and all connections to the nodes will pass through these firewalls. What must be considered about HACMP in a firewall environment?()
第2题:
A three-node cluster experienced a node failure. The resource groups were acquired as cexpected. The node has been repaired,and HACMP has been restarted. How does the operator determine that the node has successfully re-integrated into the cluster?()
第3题:
A cluster node has been started and has not acquired the resources in the resource groups. Which log file will show the details of any event script processing that has occurred?()
第4题:
An enterprise has three nodes: -Node ’A’ is a production database, -Node ’B’ is a production Application server, and -Node ’C’ is a test and development node. Node ’C’ is used by six programmers to develop and the production application as business critical and would like to make it highly available with HACMP. Application development and testing is not business critical. Which of the following describes the best solution?()
第5题:
An enterprise has two nodes: -Node ’A’ runs a large relational database and ha six CPUs and 32GB of memory. -Node ’B’ is an application server with three CPU’s and 16GB of memory. During peak production periods, the CPU load for Node ’A’ is normally between 30% and 40%. For Node ’B’, the CPU load is 10% to 20% during peak production periods. Which of the following describes the best solution for an HACMP cluster?()
第6题:
An HACMP setting timer may used to allow:()
第7题:
Perform a graceful takeover one node at a time and apply the updates.
Perform the updates on all nodes simultaneously using C-SPOC utilities.
Perform the updates on node at a time with the cluster software active.
Perform a graceful stop of all cluster nodes and apply updates to all nodes.
第8题:
/tmp/hacmp.out
/tmp/clstrmgr.debug
/usr/es/adm/cluster.log
/var/adm/hacmp/hacmp.out
第9题:
Change the cluster to a rotating design.
Change the Cascading without Fallback flag to true.
Change the Inactive Takeover field to false in the cluster configuration.
Nothing should be done. This is the default behavior for cascading resource groups,and node ’A’ should have been started first.
第10题:
Use the clstat command.
Use the cIRGinfor command.
Tail the /etc/hacmp.out file and wait for node_up_complete to finish successfully.
Tail the /usr/es/adm/cluster.log file and wait for node_up_complete to finish successfully.
第11题:
Turn off the IP core switch connecting the two nodes.
Issue the command stopsrc -g inetd on the node that has the resource group.
Issue the command sh /etc/rc.tcpclean on the node that has the resource group.
Simultaneously unplug all network cables from the node that has the resource group.
第12题:
rg1 is configured with a delayed fallback timer
Settling time policy has not been configured for rg1
Node1 does not have sufficient resources to support rg1
Node2 is the first in the ’Default Node Priority’ list for resource group rg1
第13题:
The IP subsystem fallover behavior of a two-node cluster is being testing in a large client organization. One of the tests is to simulate a network_down event and verify that HACMP movesthe single resource group to the standby node. What is the best way to simulate a network down condition?()
第14题:
A new administrator is performing fallover testing on a two-node cluster and is concerned that the cascading resource group belonging to Node ’A’ did not reintegrate properly after the cluster was restarted on Node ’A’. A stable cluster is reported by clstat,and clRGinfo reports the resource group online on Node ’B’. What type of configuration would cause this type of behavior?()
第15题:
A step in the HACMP test plan is to gracefully stop the cluster on a node and to verify that the Shared resources fallover to the standby node. To prepare for this testing step, both nodes in the two-node cluster are in a stable state with the single resource group active on Node ’A’. Which of the following is the best way to execute this portion of the test plan?()
第16题:
The first step documented in Company.com’s HACMP test plan is to start the cluster manager on the normal service node and verify that HACMP daemons have started with the ’lssrc -g cluster" command. What daemons MUST show as active in the ’lssrc -g cluster" command to have an operational cluster?()
第17题:
An administrator has a two-node PowerHA cluster in a mutual takeover configuration. He needs to updatefrom 5.5 service pack 1 to 5.5 service pack 2. Which of the following actions will perform the updates with norisk of disruption to applications running in the cluster?()
第18题:
The setting or fallback of a cluster custom resource group
The cluster time to stabilize before starting a custom resource group
A priority node time to acquire custom resource group at cluster start
A fallover node time to process custom resource states to be monitored
第19题:
clstat
clinfo
cldiag
clverify
第20题:
The resource group DNP has been configured.
The resource group option CWOF has been enabled.
The resource group option Inactive Takeover is set.
A resource group fallback timer has been configured.
第21题:
Change the cluster resource group definitions from cascading to rotating,synchronize the cluster,and restart HACMP
Edit the /urs/es/sbin/utilities/clhosts file to reflect he desired node-to-resource group relationships and restart HACMP
Use the clRGMove utility move rg2 o Node ’B’ and rg3 to Node ’C’,then start the cluster manager on Nodes ’B’ and ’C’ with the clstart utility
Disable Inactive Node Takeover,check the node priority list in the resource groups definitions,synchronize the cluster,and start HACMP on Nodes ’B’ and ’C’
第22题:
clstrmgrES,clsmuxpdES
topsvcsd,grpsvcsd,exaixos
topsvcsd,grpsvcsd,clinfoES,grglsmd
clstrmgrES,clsmuxpdES,topsvcsd,grpsvcsd
第23题:
Use thee cascading resource groups where ’rg1’ and ’rg2’ fallover to Node ’B’ and ’rg3’ falls over to Node ’C’
Use Dynamic Node Priority resource groups with a priority chain consisting of Node ’A’ then Node ’B’ then Node ’C’
Use three rotating resource groups with ’rg1’ and ’rg2’ falling over to node ’B’ and ’rg3’ falling over to Node ’C’
Upgrade Nodes ’B’ and ’C’ to be equal to Node ’A in CPU and memory resources to enable the cluster to synchronize three resource groups