Which command at the [edit protocols isis] hierarchy level forces routed traffic to avoid this router?()
第1题:
A. metric 64
B. overload
C. priority 0
D. te-metric 32768
第2题:
A. [edit policy-options]
B. [edit routing-options]
C. [edit forwarding-options]
D. [edit protocols]
第3题:
Refer to the exhibit. A company would prefer all Internet - bound OSPF routed traffic to use ISP ABC with ISP DEF as a backup. As the network consultant, what three configuration changes might you make?()
A. The default -information originate command should be configured on router B1 and B4.
B. The default -information originate command should be configured on router B2 and B3.
C. If the metric value for ISP ABC is set at the default, the I SP DEF metric value should be set to 1.
D. If the metric value for ISP ABC is set at the default, the ISP DEF metric value should be set to 25.
E. The metric type value should be set to type 1.
F. The metric type value should be set to type 2.
第4题:
At which command prompt would you issue the set date
第5题:
In which hierarchy are routing policies defined?()
第6题:
At which two levels of the Junos CLI hierarchy is the host-inbound-traffic command configured? ()(Choose two.)
第7题:
You are configuring new BGP neighbor and want to view the configuration for the interface ge-0/0/0.42.Which command do you use to achieve this result?()
第8题:
An IS-IS router is adjacent to and passing traffic with a neighbor. You perform a show is interface detail command and notice that for some interfaces you have a circuit type of 3. Which IS-IS level(s) is enabled on these interfaces?()
第9题:
Which command at the [edit protocols isis] hierarchy level forces routed traffic to avoid this router?()
第10题:
[edit policy-options]
[edit routing-options]
[edit forwarding-options]
[edit protocols]
第11题:
[edit chassis] user@router#
[edit] user@router#
[edit system] user@router#
user@router>
第12题:
Level 1 only
Level 2 only
Level 1 and Level 2
Level 3 only
第13题:
A. set protocols rsvp cspf-enable
B. set protocols mpls cspf-enable
C. set protocols rsvp traffic-engineering
D. set protocols ospf traffic-engineering
第14题:
A. Configure the net system - id command under routerisis and enable IS - IS on each interface with the ip router isis command.
B. Configure the net sy stem - id and the network net - id commands under routerisis.
C. Configure the network net - id command(s) under routerisis and enable IS - IS on each interface with the ip router isis command.
D. Configure the network net - id command(s) and the is - type level -1- 2 command under routerisis.
E. Configure the net system - id and the network net - id commands under routerisis and enable ISIS on each interface with the ip router isis command.
第15题:
An IS-IS router is adjacent to and passing traffic with a neighbor. You perform a show isis interface detail command and notice that for some interfaces you have a circuit type of 3. Which IS-IS level(s) is enabled on these interfaces?()
第16题:
You want to allow your device to establish OSPF adjacencies with a neighboring device connected tointerface ge-0/0/3.0. Interface ge-0/0/3.0 is a member of the HR zone.Under which configuration hierarchy must you permit OSPF traffic?()
第17题:
Which CLI command shows if the router has formed any IS-IS adjacencies?()
第18题:
In JUNOS software, which command is used to configure TED support for OSPF?()
第19题:
You are modifying the default route preference under the [edit protocols] hierarchy. In which two routing information sources can you change the default preference value?()
第20题:
Which CLI command displays the IS-IS level used by each interface?()
第21题:
Under which Junos hierarchy level are security policies configured?()
第22题:
[edit security]
[edit protocols]
[edit firewall]
[edit policy-options]
第23题:
[edit security idp]
[edit security zones security-zone trust interfaces ge-0/0/0.0]
[edit security zones security-zone trust]
[edit security screen]
第24题:
metric 64
overload
priority 0
te-metric 32768