Incorrect VTP domain
Incorrect VTP password
Incorrect VTP mode
Incorrect VTP configuration revision
第1题:
Which configuration option will cause the link between two Cisco 3600 Series Multiservice Platforms to become a functional trunk?()
第2题:
You are deploying two core switches, one in each building, 50 km away from each other. The cross-connection between them will be a Layer 2 2-gigabit EtherChannel with an 802.1Q trunk. You configured it correctly but the link does not come up. The port is in the "admin up" state, and the line protocol is in the "down" state. The fiber link is OK. What would be the most likely reason for the link not to come up? ()
第3题:
Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.What will happen in this scenario?()
第4题:
You have a trunk link operating between two switches and you’re experiencing problems withframes leaking between the two VLANs. Each switch has identical modules, software revisionsand VLAN configuration information. Spanning tree protocol is disabled on all VLANs. What isprobably causing this problem?()
第5题:
You are deploying two core switches, one in each building, 50 km away from each other. The cross-connection between them will be a Layer 2 2-gigabit EtherChannel with an 802.1Q trunk. You configured it correctly but the link does not come up. The port is in the "admin up" state, and the line protocol is in the "down" state. The fiber link is OK. What would be the most likely reason for the link not to come up?()
第6题:
An 802.1Q trunk is not coming up between two switches. The ports on both switches are configured as "switchport mode desirable." Assuming that there is no physical issue, choose two possible causes.()
第7题:
A switch port on TK1 is being configured to support 802.1Q trunking. Which of the following are true about 802.1Q trunking?()
第8题:
A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this?()
第9题:
open
uncover
covered
closed
第10题:
Set each end of the trunk line to IEEE 802.1Q encapsulation.
Set the same VTP management domain name on both switches.
Set all ports on the two switched as access ports.
Configure one of the two switches as a VTP server.
Connect the two switches using a rollover cable.
Use a router to forward VTP traffic between the VLANs.
第11题:
All VLANs except the default VLAN will be removed from all switches.
All existing switches will have the students, admin, faculty, Servers, Management,Production, and no-where VLANs.
The VLANs Servers, Management, Production, and no-where will replace the VLANs on SwX.
The VLANs Servers, Management, Production, and no-where will be removed from existing switches.
第12题:
A root VTP server
A trunk port
VTP priority
VLAN 1
None of the other alternatives apply
第13题:
Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13.An 802.1Q trunk is configured between the two switches.On CAT1,VLAN10 is chosen as native,but on CAT2 the native VLAN is not specified.What will happen in this scenario?()
第14题:
You need to investigate a VTP problem between two Company switches. The lack of which two prevents VTP information from propagating between switches?()
第15题:
Refer to Topic TestKing.com in iPAD document.What happens to the network when TestKingX is reconnected and a trunk exists between the two switches?()
第16题:
You are configuring an 802.1Q trunk between a Layer 2 switch and a firewall. You read in the documentation that the best way to set up a trunk is to set the port as dynamic desirable. The trunk is not coming up. Which one of these options would be a valid explanation? ()
第17题:
Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802. 1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.What will happen in this scenario?()
第18题:
The network administrator is trying to add Switch1 to the network, but the 802.1Q trunk is not coming up. Switch1 was previously tested in the laboratory and its trunk configuration worked fine. What are three possible causes of this problem? ()
第19题:
If you were to configure an ISL Ethernet trunk between two Cisco switches, named R1 and R2, what would you have to include at the end of the link for the trunk to operate correctly? ()
第20题:
shut
closing
opened
closed
第21题:
The switches are not the same model
You are not using the correct SFP
You are not using correct optical media converters
Configuration should be modified, because the distance is longer
第22题:
The trunking configuration mode on Switch1 is set to Off.
The trunking configuration mode on the other end is set to On.
The trunking configuration mode on the other end is set to Desirable.
Cisco Discovery Protocol is not running on the other end.
There is a VTP domain name mismatch.
Switch1 does not support 802.1Q
第23题:
The Cisco Control VLAN carries only Layer 2 control traffic
802.1Q trunking is used between the access switch and the router
There is no 802.1Q trunking used in these designs
When 802.1Q trunks are configured, they are also called Native VLANs
Trunking Ensures that traffic from only one VLAN is carried on that trunk
第24题:
The link is using IEEE 802.1Q protocol
The link is using IEEE 802.1E protocol
Spanning tree is disabled
Not enough information to determine
The native VLAN information is identical at each end of the link
The native VLAN information is different at each end of the link