Loopback 0
management
internal(fxp1)
control interface
第1题:
A.It is only used for exception traffic.
B.It is an FE link called fxp2.
C.It is rate-limited to avoid DDOS attacks.
D.It is only used to send the forwarding-table from the Routing Engine to the Packet-Forwarding Engine.
第2题:
The TestKingA router is configured as shown below:TestKingA(config) interface loopback 0TestKingA(config-if) ip address 192.168.16.24 255.255.255.255As a result of this change, which of the statements below are true?()
A. It creates a virtual, software only, interface.
B. It provides a way to test the convergence of OSPF routing updates.
C. The mask of 255.255.255.255 is called a host mask.
D. It uses a wildcard mask of 255.255.255.255.
E. It ensures that an interface is always active for OSPF processes.
F. Loopback interfaces must be numbered 0.
第3题:
On a Cisco Unified Computing System (UCS), which two statements regarding Ethanalyzer are true?()
第4题:
Which statement is true regarding the forwarding plane?()
第5题:
What is the interface connecting the routing engine to the packet forwarding engine called?()
第6题:
If the PFE does not have a route to the destination address of a packet, which action will be taken?()
第7题:
Whitch two statements are true regarding the role of the Routing Engine (RE)? ()
第8题:
It is only used for exception traffic.
It is an FE link called fxp2.
It is rate-limited to avoid DDOS attacks.
It is only used to send the forwarding-table from the Routing Engine to the Packet-Forwarding Engine.
第9题:
Loopback 0
management
internal(fxp1)
control interface
第10题:
They purge any routes not selected as active routes.
They exist in two places: the Routing Engine and the Packet Forwarding Engine.
They are exclusively designed to handle dynamic routing protocols.
They populate the forwarding table.
第11题:
Wireless LAN Solution Engine (WLSE)
command-line interface (CLI)
Wireless Control System (WCS)
TFTP
an HTTPS web user interface
an HTTP web user interface
第12题:
Set up the Network Time Protocol server.
Install the files needed to run the web-based GUI.
Set up routing and IP addressing on the service module and the interface service engine.
Configure a session initiation protocol dial peer for connecting calls to the voice mail and Auto Attendant features.
第13题:
A.Loopback 0
B.management
C.internal(fxp1)
D.control interface
第14题:
Which three user interfaces exist for the Cisco WLAN Controllers?()
第15题:
What must be configured on the Cisco Unity Express host router prior to installation of the CUE module?()
第16题:
Which two statements are true regarding the role of the Routing Engine (RE)?()
第17题:
For which two functions is the Routing Engine responsible?()
第18题:
Which two field-replaceable units FRUs are hot-swappable?()
第19题:
Which statement is true about routing tables on a Junos device?()
第20题:
The forwarding plane is contained within the Routing Engine (RE)
The forwarding plane processes and evaluates exception traffic
The forwarding plane contains the Packet Forwarding Engine (PFE)
The forwarding plane is not present on all platforms running the Junos OS
第21题:
The PFE floods the packet out of all interfaces.
The PFE drops the packet and sends a destination unreachable notification back to source device.
The PFE forwards the packet to the routing engine for furtherprocessing.
The PFE queues the packet and sends are quest for a layer3 lookup to the routing engine.
第22题:
The RE controls and monitors the chassis.
The RE manages the Packet Forwarding Engine (PFE).
The RE receives a copy of the forwarding table from the forwarding plane.
The RE implements class of service (COS).
第23题:
Only the router A loopback interface is parti cipating in the OSPF routing process
None of the router A interfaces are participating in the OSPF routing process
Router A is using the loopback interface IP address as its OSPF router ID
Router A does not have any reachable OSPF neighbors
第24题:
Configure Routing Information Protocol (RIP), and then activate authentication on the RIP interface.
Configure Routing Information Protocol (RIP), and then configure the incoming packet protocol settings on the RIP interface.
Configure Network Address Translation (NAT), and then add a new service to the NAT interface.
Configure Network Address Translation (NAT), and then enable the Secure Web Server (HTTPS) service on the NAT interface.