Transfer the file to the FC module using FTP; use Telnet to the FC module to start the update
Use Telnet to the AMM to transfer the file using TFTP; start the update
Transfer the file to the FC module using Secure Copy Protocol (SCP);use Telnet to the FC module to start the update
Start the update and enter FC module IP address when prompted
第1题:
Which of the following does an out-of-memory error indicate on a printer?()
第2题:
Which is a supported method to upgrade firmware on an IBM Power Systems 570?()
第3题:
Which is a supported method to upgrade firmware on an IBM Power Systems 570?()
第4题:
A customer has two Ethernet Switch Modules installed in an IBM BladeCenter Enterprise chassis. The modules were configured identically. The Ethernet module in bay one was inadvertenly reset to factory defaults. Which solution returns the module to the customer-specific configuration?()
第5题:
A customer has purchased a new Junos Pulse Access Control Service and wants to install it in an existing cluster.After initial configuration, the customer finds that the firmware version running on the Junos Pulse Access Control Service is 4.1 r5, but the existing cluster is running firmware version 4.1 r3. Which two actions must be performed to allow the new Junos Pulse Access Control Service to load the older version of firmware?()
第6题:
A large customer location world-wide needs to remotely update UEFI Firmware on their systems. Which function of IBM System Director will help this customer?()
第7题:
Automation Manager
Update Manager
System Maintenance and Update Tool
Service and Support Manager
第8题:
Back up the AMM configuration to a file
Back up the AMM configuration to the chassis
Back up the AMM using IBM Systems Director
Back up the AMM using Tivoli Storage Manager
第9题:
4GB Modular Flash Drive for each Blade Server and Dual 15.8GB 2.5 Solid State Drive for each Blade Server
Cisco Intelligent Gb Ethernet Switch Module and IBM BladeCenter Copper Pass-thru Module
Fibre Channel Expansion Card for each Blade Server and Fibre Channel SAN Switch Module
Cisco Intelligent Gb Ethernet Switch Module and Dual 15.8GB 2.5 Solid State Drive for each Blade Server
第10题:
Use the /usr/sbin/invscout AIX command.
Use the ’Updates’ panel on the managing HMc
Boot the 570 using an IBM-provided microcode Cd
Use the /usr/lpp/diagnostics/bin/update_flash AIX command.
第11题:
collect all support data
implement a current backup
update all firmware levels
shut down the storage system
第12题:
Copper Pass-thru Modules only support 1000Mb line speeds.
Spanning Tree has been enabled on the Copper Pass-thru Module.
The customer does not have the latest firmware loaded on the Copper Pass-thru Module.
The customer is using LS21 Blades
第13题:
By default, who is responsible for firmware and software updates of an SVC solution? ()
第14题:
A retail customer installs a BladeCenter into an existing 10/100 Ethernet network. Due to cost considerations, the customer uses Copper Pass-thru Modules. After installing this solution, the customer finds that they have no network connectivity. Which of the following at is causing the problem?()
第15题:
A customer wants to install an IBM BladeCenter infrastructure but is concerned about the cost of the internal fibre switches. Consequently. the customer wants to use the Optical Pass-Thru Module (OPM). What TRUE statement should be mentioned to the customer regarding the OPM?()
第16题:
A customer has downloaded new firmware files for the IBM support Web Site. Which of the following is the correct method for updating the firmware for the QLogic Intelligent Passthru Module using the command line?()
第17题:
Which IBM System Director task will give you the ability to update firmware and device drivers on System x servers?()
第18题:
Back up the configuration from Ethernet module in bay 2 and restore it to the module in Bay 1 using the switch CLI or Web interface
Swap the modules, which will automatically resynch the settings stored in the Advanced Management Module
Back up the configuration of the Ethernet module in bay one and restore it to the Ethernet module in bay two using the AMM
Restore the configuration from NVRAM using the Switch Module Web interface
第19题:
Transfer the file to the FC module using FTP; use Telnet to the FC module to start the update
Use Telnet to the AMM to transfer the file using TFTP; start the update
Transfer the file to the FC module using Secure Copy Protocol (SCP);use Telnet to the FC module to start the update
Start the update and enter FC module IP address when prompted
第20题:
Use the /usr/sbin/invscout AIX command
Use the 'Updates' panel on the managing HMC
Boot the 570 using an IBM-provided microcode CD
Use the /usr/lpp/diagnostics/bin/update_flash AIX command
第21题:
Configure the box with RAID-1 and not RAID-5.
Disable Hyperthreading feature on the machine.
Ensure the Watchdog timers on the RSA-II are disabled.
Replace the Windows NTLDR file on the root partition from another copy of the Windows OS files.
第22题:
The primary line module is inactive for five minutes and then becomes active.
The primary line module is in standby mode,while the spare line module remains active.
The primary line module becomes active immediately and the spare line module becomes inactive.
The primary and spare line modules are active for five minutes,after which time the spare line module becomes inactive.
第23题:
Open a Web browser and log on to the IMM; in the navigation frame, click IMM Firmware Update under IMM Control; click Browse; select the .exe file; click the Upgrade/Update button
TFTP to the AMM; from the Main Menu, select Update; browse to the downloaded .exe file
Telnet to AMM; from the Main Menu, select Update; browse to the downloaded .pkt file
Open a Web browser and log on to the AMM; in the navigation frame, click AMM Firmware Update under AMM Control; click Browse; select the .pkt file; click the Upgrade/Update button
第24题:
A faulty memory module in the printer.
A postscript print job has been sent to the printer.
A large print job has been sent to the printer.
The printer firmware needs to be updated.