Insert the ServerGuide CD/DVD, boot the HX5 blade and follow the prompts
Boot the blade from the HX5 Bootable Media Creator (BoMC) and follow the prompts
Press F1 when the HX5 system is booting, select Update UEFI, insert the CD/DVD and select OK
Mount the IMM virtual disk
第1题:
A blade server has been configured to boot from SAN. After an HBA firmware upgrade the blade was rebooted and cannot find the operating system. Which of the following should the administrator do NEXT to troubleshoot the issue?()
第2题:
During system boot, the system hangs at LED 0C31. What is the first step the system administrator should take to correct the problem?()
第3题:
A customer has the following equipment installed in their data center: (1)an IBM BladeCenter H chassis (2)two power supplies (3)six HS22V blades (4)three Nortel 1/10 GB ESMs The retail customer purchased a new HX5 with MAX5. Which of the following must be added to install the HX5 with MAX5?()
第4题:
Customer requests a HX5 blade but his application may demand more than its 16 memory DIMMS. Software licensing is a big concern. Which of the following additions meets this requirement? ()
第5题:
QUESTION 14 You have a computer that contains a DVD drive and a single 350-GB hard disk drive. You attempt to installWindows 7 on the computer by using the DVD installation media and receive the following error message:Reboot and Select proper Boot device or Insert Boot Media in selected Boot device. You need to ensurethat you can install Windows 7 on the computer by using the DVD installation media. What should you do?()
第6题:
An A+ Certified Technician MUST do an install on a Windows XP system from the distribution CD. However, the system does not boot from this CD. What is the MOST likely cause of this problem?()
第7题:
InstallServerGuide CD/DVD,boot the HX5 blade and follow the prompts
Boot the blade from the HX5 Bootable Media Creator (BoMC) and follow the prompts
Press F1 while the HX5 is booting,incert the CD/DVD and select OK
Mount the IMM virtual disk
第8题:
Verify all HBA settings.
Upgrade the blade firmware.
Upgrade the OS level HBA drivers.
Set the system to boot from the local disk.
第9题:
From the BIOS, modify the startup order.
From the BIOS, enable Pre-Boot Execution Environment (PXE).
Create an answer file named oobe.xml and place the file on the hard disk drive.
Create an answer file named autounattend.xml and place the file on the hard disk drive.
第10题:
32U
25U
22U
21U
第11题:
Another HX5
MAX5
HS22V
x3850 X5
第12题:
Fibre Channel Expansion Card for each Blade Server
cKVM Card for each Blade Server
iSCSI Expansion Card for each Blade Server
4Gb Modular Flash Drive
第13题:
What is the correct procedure to update the UEFI on HX5 with MAX5 blades without using the AMM?()
第14题:
A customer wants to boot from an iSCSI SAN with their IBM BladeCenter infrastructure running Microsoft Windows Server 2000. What is required for the customer to be able to perform this?()
第15题:
Which of the following is the correct procedure to update the BIOS on LS42 blades without using the AMM?()
第16题:
A customer wants a Blade to run a very memory intensive application. They require 48 GB with later expansion to 160 GB using 4 GB DIMMs. Which of the following products supports this requirement?()
第17题:
A medical customer has an installed HS21 blade with no local disk. They are attempting to set up boot from SAN using a Windows 2003 CD. Which sequence is correct for this procedure? ()
第18题:
Insert the ServerGuide CD/DVD, boot the HX5 blade and follow the prompts
Boot the blade from the HX5 Bootable Media Creator (BoMC) and follow the prompts
Press F1 when the HX5 system is booting, select Update UEFI, insert the CD/DVD and select OK
Mount the IMM virtual disk
第19题:
32U
21U
25U
22U
第20题:
Two additional power supplies
Fibre Channel (FC) switches and SAN storage
A Nortel 1/10 GB ESM
SSD for the HX5
第21题:
Install Windows from the CD using the QLogic driver provided on the CD, configure the LUN and zone for the target server, and then configure the blade UEFI to boot from SAN.
Configure the LUN and zone for the target server, install Windows from the CD and press F6 when prompted to supply the driver, and then configure the QLogic adapter BIOS to boot from SAN.
Configure the LUN and zone for the target server, configure the QLogic adapter BIOS to boot from SAN, install Windows from the CD, and then press F6 when prompted to supply the driver.
Configure the blade UEFI to boot from SAN, configure the LUN and zone for the target server, and then install Windows from the CD using the QLogic driver provided on the CD
第22题:
The CD is defective.
The CD is not bootable.
The CD-ROM drive is defective.
The Boot Sequence is not set in the BIOS to boot first from the CD
第23题:
4
3
2
8
第24题:
Insert the Update eXpress Service Pack Installer (UXSPI) CD, boot the LS42 blade and follow the prompts
Boot the blade to the Bootable Media Creator (BoMC) CD and follow the prompts
Press F1 when the LS42 system is booting, select Update BIOS, insert the diskette into the diskette drive, and select OK
Use the Remote Supervisor Adapter virtual disk