Change System User Interface
TCP/IP Further Configuration
TCP/IP Minimum Configuration
Network Installation Management
第1题:
You are the administrator of Company.com's Windows 2000 Network. The routed TCP/IP network that you administer consists of 10 Windows 2000 Server computers and 75 Windows 2000 Professional computers. All computers are members of a single Windows 2000 domain named Company.com. TCP/IP is the only network protocol used at Company's office. You have recently installed 10 new Windows 2000 Professional computers and you want to enable the new computers to use host names to connect to shared resources on the network. You configure a TCP/IP address and a gateway address on each new computer. You want to complete the configuration to allow the computers to communicate on the network. What should you do?()
第2题:
Which of the following is the FIRST thing that should be done in order to begin reinstalling TCP/IP on the server?()
第3题:
When connecting a laser printer to a network for the first time, a technician should FIRST:()
第4题:
Your routed TCP/IP network consists of 10 Windows 2000 Server computers and 75 Windows 2000 Professional computers. Your network uses TCP/IP as the only network protocol. You are installing 10 new Windows 2000 Professional computers. You want to enable the new computers to use NetBIOS names to connect to all shared resources as the network. You configure a TCP/IP address and a subnet mask on each new computer. Which 2 additional TCP/IP properties should you configure on each new computer?()
第5题:
You are the network administrator for your company. The network consists of a single Active Directory domain. All computers on the network are members of the domain. You administer a three-node Network Load Balancing cluster. Each cluster node runs Windows Server 2003 and has a single network adapter. The cluster has converged successfully. You notice that the nodes in the cluster run at almost full capacity most of the time. You want to add a fourth node to the cluster. You enable and configure Network Load Balancing on the fourth node. However, the cluster does not converge to a four-node cluster. In the System log on the existing three nodes, you find the exact same TCP/IP error event. The event has the following description: "The system detected an address conflict for IP address 10.50.8.70 with the system having network hardware address 02:BF://0A:32:08:46." In the System log on the new fourth node, you find a similar TCP/error event with the following description: "The system detected an address conflict for IP address 10.50.8.70 with the system having network hardware address 03:BF://0A:32:08:46." Only the hardware address is different in the two descriptions. You verify that IP address 10.50.8.70 is configured as the cluster IP address on all four nodes. You want to configure a four-node Network Load Balancing cluster. What should you do? ()
第6题:
Your Company upgrades its network to 100 Mbps. You remove the old network adapter and install a new 10/100 Mbps network adapter into a Windows 2000 Professional computer. You configure the TCP/IP protocol settings to be the same as they were for the previously installed network adapter. When you restart eh computer, however, you cannot access the network. You try to ping your network adapter’s TCP/IP address locally. You receive the following error message. “Request timed out.” Next, you try to ping 127.0.0.1 and receive the same error message. What must you do?()
第7题:
TCP
UDP
ICMP
SMTP
第8题:
IP address
Check the Use default gateway on remote network checkbox
Disable Use IP compression
On the WINS tab of the TCP/IP Settings, check the Use NetBIOS setting from the DHCP-Server
On the DNS tab of TCP/IP settings, check the Register this connections address in the DNS checkbox
第9题:
The system’s local time settings
The system’s O/S version and patch status
The system’s network configuration
The mail server’s configuration
第10题:
Change System User Interface
TCP/IP Further Configuration
TCP/IP Minimum Configuration
Network Installation Management
第11题:
PING
NETSTAT
NET
TRACERT
第12题:
Configure netsh settings in case of backup
Restart the server
Notify users
Uninstall TCP/IP
第13题:
Which of the following SMIT panel screens are used to configure a system’s basic network parameters for the very first time only?()
第14题:
A user states that all their incoming mail is showing that it is behind three hours. All other users have the correct time. Which of the following should the technician check?()
第15题:
In a TCP/IP network, which of the following protocols is involved when a user issues a ping command?()
第16题:
You dial-in to your company’s network from home. You notice that you can only access resources only on the first subnet (where the Dial-In Server is located), but cannot go beyond that. What Dial-In setting should you change?()
第17题:
You are the network administrator for Company. Company has recently upgraded its network to a 100Mbps standard and you are now in the process of removing all the old adapter and installing a new Token Ring network adapter into the Windows 2000 Professional computer. On the first computer you install the new hardware and configure the static TCP/IP protocol settings to be the same as they were for the previously installed network adapter. When you restart the computer, however, you cannot access the network. You try to ping your network adapter's TCP/IP address locally. You receive the following error message: "Request timed out." You want to enable the computer to communicate on the new network. What should you do? ()
第18题:
Enable DHCP in the TCP/IP properties.
Replace the Token Ring network adapter with an Ethernet network adapter.
Configure a different TCP/IP address on the same subnet.
Configure a valid DNS Server in the TCP/IP properties.
第19题:
Windows 2000 Server >> Network >> Binding >> Server >> TCP/IP on the top.
Windows 2000 Server >> Network >> Binding >> Workstation >> TCP/IP on the top.
Windows 2000 Professional >> Network >> Binding >> Server >> TCP/IP on the top.
Windows 2000 Professional >> Network >> Binding >> Server >> TCP/IP on the bottom.
Windows 2000 Professional >> Network >> Binding >> Workstation >> TCP/IP on the top.
Windows 2000 Professional >> Network >> Binding >> Workstation >> TCP/IP on thebottom.
第20题:
rcp
tftp
ping
rpcinfo
第21题:
Configure a different TCP/IP address
Enable DHCP in the TCP/IP properties
Enable DNS in the TCP/IP properties
Configure the network adapter to run at 100 Mbps only
Replace the network adapter.
第22题:
Configure the fourth node to use multicast mode.
Remove 10.50.8.70 from the Network Connections Properties of the fourth node.
On the fourth node, run the nlb.exe resume command.
On the fourth node, run the wlbs.exe reload command.
第23题:
The wild card mask
The IP address
The IP address mask
The metric weights
The Autonomous System number
第24题:
no
nfso
vmtune
exportfs