lsattr -El tty2
lscons -d /dev/tty2
lscfg -vl tty2
what /dev/tty2
第1题:
A modem is set up for a remote TTY connection that will become the system console. How should one verify that the console is enabled as the system console after the next reboot?()
第2题:
Which of the following commands should be used to check whether a system dump is valid and readable?()
第3题:
Which of the following command can be used to identify all PCI hot plug slots on a server and their characteristics()
第4题:
A system administrator is attempting to unmount filesystem /dev/data and receives the following message: umount: 0506-349 Cannot unmount /dev/data: The requested resource is busy. Which of the following commands can be used to determine which process has open references within the filesystem?()
第5题:
Which of the following commands should be used to open a tty port configured in the /etc/uucp/Devices file as: Direct tty2 - 9600 direct in debug mode, ignoring modem control signal data carrier detect (DCD)?()
第6题:
A system administrator has an application that has the data in volume group appvg. Which of the following commands will back up the contents of appvg to the tape in /dev/rmt0 and check for any read errors?()
第7题:
Which of the following commands will list vital product data for all hardware components on a server?()
第8题:
lscons -b
lscons -d
lscons -s
swcons /dev/tty0
第9题:
lspv -pv hdisk2
lsattr -El hdisk2
lsdev -dev hdisk2 -attr
lspath -dev hdisk2 -attr
第10题:
chdev
cfgmgr
vmtune
schedtune
第11题:
cu -l tty2
cu -dml tty2
cu -dht Direct
cu -s9600 -l tty2
第12题:
savevg -mf /dev/rmt0 appvg
savevg -cvf /dev/rmt0 appvg
savevg -vf /dev/rmt0 appvg
savevg -f /dev/rmt0 -V appvg
第13题:
The administrator would like to verify that hdisk2 has the correct reserve policy set. What IOS command should the administrator run?()
第14题:
Which of the following commands should be used to identify packet sequence problems?()
第15题:
A System p administrator has an application that has the data in volume group appvg. Which of the following commands will back up the contents of appvg to the tape in /dev/rmt0 and check for any read errors ()
第16题:
Which of the following commands should be used to tune parameters of devices that are displayed with lsattr?()
第17题:
Which of the following commands can be used to identify all PCI hot plug slots on a server and their characteristics?()
第18题:
Which of the following commands should be used to check the settings for a new tty that was just set up as tty2?()
第19题:
A system administrator has created tty2 on a serial port connection to a system. When attempting to verify the connection the following error is observed: # cu -ml tty2 cu: 0835-028 The connection failed. NO DEVICES AVAILABLE. Which of the following should be performed to correct this error?()
第20题:
Create an entry for tty2 in the /etc/uucp/Devices file
Re-enter the command as cu -dml tty2
Create an entry for tty2 in the /etc/uucp/Systems file
Re-enter the command as cu -s 9600 -dh -t -l tty2
第21题:
lsfs
topas
fuser
mount
第22题:
kdb
snap -d
dbx -vmcore
od /dev/sysdumpdev
第23题:
savevg -mf /dev/rmt0 appvg
savevg -cvf /dev/rmt0 appvg
savevg -xvf /dev/rmt0 appvg
savevg -f /dev/rmt0 -V appvg