Shuts down en0
Displays en0 settings
Reconfigures en0 using the ODM
Sends an SNMP alert to the network administrator
第1题:
The en0 interface on Node1 of a two-node cluster has failed. This adapter is configured with a boot addressand under stable operations also has the service address of the cluster’s single resource group. The resourcegroup is configured with the fallback option. The HA network was configured for IPAT via aliasing and now theservice address is on the en1 interface in the cluster. The en0 interface has already been physically replacedand configured with the boot address. Which of the following will return the cluster to its original state andminimize cluster downtime?()
第2题:
Which of the following commands will set the duplex of a network adapter?()
第3题:
How is an IP address removed from a network interface?()
第4题:
Which of the following functions does the "ifconfig en4 down" perform?()
第5题:
A System p administrator must change the 9.47.53.0 subnet from 128 addresses to 64 addresses. How can the AIX systems in the network be permanently modified to accomplish this()
第6题:
en0 has no associated ip address.
serverB is missing its default route.
serverB and serverA cannot connect due to a firewall.
en0 has been set up to block traffic from servers that are in different subnets.
第7题:
rmdev -dl ent0
ifconfig en0 down
ifconfig en0 delete
ifconfig ent0 detach
第8题:
mktcpip -h hostname -a 9.47.53.x -m 255.255.255.64 -i en0 -g 9.3.230.1
ifconfig en0 netmask 255.255.255.64
chdev -l en0 -a netmask=255.255.255.192
ifconfig en0 netmask 0xffffffc0
第9题:
Multicast addressing
Load balancing
Address translation
DHCP
第10题:
Removes the en4 interface
Removes the en4’s network route
Stops all traffic through the en4 interface
Stops all traffic through the en4 and removes its network route from the routing table
第11题:
en0 has no associated ip address.
serverB is missing its default route.
serverB and serverA cannot connect due to a firewall.
en0 has been set up to block traffic from servers that are in different subnets.
第12题:
entstat -d
ifconfig -a
lsattr -El en0
odmget -q name=ent0 and attribute=netaddr CuDv
第13题:
A system administrator has determined that there is no network connectivity with the en0 interface. By doing a netstat -in, it is determined that the en0 interface is not showing up. Which of the following commands should be used to determine that en0 is defined in ODM with an IP address?()
第14题:
Data is transferred between two servers using NFS, where one server is configured with token ring, and the other system is configured with ethernet. It is discovered that the performance is greatly reduced during this transfer. Which of the following steps should be taken to improve performance?()
第15题:
After updating serverB’s network configurations, an administrator notices that serverA, which resides in a different subnet, is unable to communicate with serverB via ssh or telnet. As ping’s to the server fail, the administrator logs onto serverB via a console and finds an available interface en0 in the ’up’ state. From the console connection, en0 can communicate with other servers in the same subnet. What is the most likely cause of the problem?()
第16题:
How should TCP/IP be configured on the ent0 network adapter?()
第17题:
How should TCP/IP be configured on the ent0 network adapter?()
第18题:
no -a media_speed=100_Full_Duplex en0
ifconfig -a media_speed=100_Full_Duplex ent0
chdev -l ent0 -a media_speed=100_Full_Duplex
chinet -l en0 -a media_speed=100_Full_Duplex en0
第19题:
Run cluster synchronization.
Restart cluster services on Node1.
Perform a swap_adapter using C-SPOC
Restart cluster services on both nodes
第20题:
Setting up a custom community name
Configuring the network to block traffic on port 161
Configuring the Windows Firewall to block port 161
Setting SNMP to read only on the devices
Installing new MIBs
第21题:
Reduce MTU on token ring system to match ethernet system using ifconfig command (i.e. ifconfig tr0 mtu 1500)
Reduce MTU on token ring system to match ethernet system using no command (i.e. no -o mtu=1500)
Increase MTU on ethernet system to match token ring system using ifconfig command (i.e. ifconfig en0 mtu 4096)
Increase MTU on ethernet system to match token ring system using no command (i.e. no -o mtu=4096)
第22题:
Shuts down en0
Displays en0 settings
Reconfigures en0 using the ODM
Sends an SNMP alert to the network administrator
第23题:
ifconfig en0 192.168.10.1 netmask 255.255.255.0 gateway 192.168.10.254
ifconfig ent0 192.168.10.1 netmask 255.255.255.0 gateway 192.168.10.254
mktcpip test61 -a 192.168.10.1 -i en0 255.255.255.0 192.168.10.254 -smktcpip ? test61 -a 192.168.10.1 -i en0 ? 255.255.255.0 ? 192.168.10.254 -s
mktcpip test61 -a 192.168.10.1 -i ent0 255.255.255.0 192.168.10.254 -smktcpip ? test61 -a 192.168.10.1 -i ent0 ? 255.255.255.0 ? 192.168.10.254 -s
第24题:
ifconfig en0 192.168.10.1 netmask 255.255.255.0 gateway 192.168.10.254
ifconfig ent0 192.168.10.1 netmask 255.255.255.0 gateway 192.168.10.254
mktcpip h test61 -a 192.168.10.1 -i en0 m 255.255.255.0 g 192.168.10.254 -s
mktcpip h test61 -a 192.168.10.1 -i ent0 m 255.255.255.0 g 192.168.10.254 -