Enable ipforwarding only
Configure an alias on the same interface and enable ipforwarding
Add a second interface into the same subnet and enable ipforwarding
Add a second interface into a different subnet, and enable ipforwarding
第1题:
Which of the following is not an essential prerequisite for AutoQoS to be correctly applied to an interface()
第2题:
Which of the following statements regarding the use of multiple access lists are valid when configuring a single interface on a Cisco router?()
第3题:
Company.com wishes to use HACMP on two IBM eServer pSeries servers. During the planning session, it was decided to use the native serial ports s1 or s2 for a non-IP heartbeat network. What should be done to ensure the serial network will function with HACMP heartbeats?()
第4题:
Refer to the exhibit. A junior network administrator was given the task of configuring port security on SwitchA to allow only PC_A to access the switched network through port fa0/1. If any other device is detected, the port is to drop frames from this device. The administrator configured the interface and tested it with successful pings from PC_A to RouterA, and then observes the output from these two show commands.Which two of these changes are necessary for SwitchA to meet the requirements? ()
第5题:
A machine’s ONLY external interface is configured with an address of 192.168.5.1 and a netmask of 255.255.255.0. No slots are available for expansion. Which of the following procedures should be performed to make it function as a gateway?()
第6题:
Which two statements regarding external authentication servers for firewall user authentication are true?() (Choose two.)
第7题:
The interface is not plumbed.
The interface is not configured.
The interface does not have valid routes configured.
The interface is not marked as
第8题:
An interface can only belong to single Flex Links.
An interface can belong to multiple Flex Links.
Flex Links operate only over single pairs of links.
Flex Links automatically disable STP so no BPDUs are propagated.
第9题:
Up to three external authentication server types can be used simultaneously.
Only one external authentication server type can be used simultaneously.
If the local password database is not configured in the authentication order, and the configured authentication server is unreachable, authentication is not performed.
If the local password database is not configured in the authentication order, and the configured authentication server rejects the authentication request, authentication is not performed
第10题:
Port security needs to be globally enabled.
Port security needs to be enabled on the interface.
Port security needs to be configured to shut down the interface in the event of a violation.
Port security needs to be configured to allow only one learned MAC address.
Port security interface counters need to be cleared before using the show command.
The port security configuration needs to be saved to NVRAM before it can become active.
第11题:
It is applied only on the input interface of a router.
It is applied only on the output interface of a router.
It can be configured either on the input or output interface of a router.
It cannot be configured on a router interface.
It is configured under any routing protocol process.
第12题:
The interface you configured for AutoQoS is set to half-duplex
AutoQoS was configured on only one end of the link
The interface you configured for AutoQoS has no IP address
The interface’s bandwidth is not correctly configured
CEF is not enabled on the interface
You enabled AutoQoS on the interface but forgot to enable globally first
第13题:
Which of these statements accurately identifies how Unicast Reverse Path Forwarding can be employed to prevent the use of malformed or forged IP sources addresses?()
第14题:
Which statements is true about Foreign Exchange Station (FXS) ports on a router?()
第15题:
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?()
第16题:
When using a mksysb and base media to clone a system, which of the following will cause the installation to fail()
第17题:
System, machine, and user policies can be configured though AccessAdmin. How are changes synchronized with the AccessAgent?()
第18题:
Use either s1 or s2 port configured as a TTY interface with a NULL Modem cable.
Use the s2 serial port on each system configured as a TTY interface with a NULL modem cable.
Use the s1 port on each system configured as a TTY interface with a standard serial modemcable.
Verify with IBM support which native serial ports for the server model can be used for HACM pheartbeats.
第19题:
/etc/nodename
/etc/hostname.rtls0
/etc/hostname
/etc/inet/hosts
/etc/domainname
/etc/inet/ipnodes
/etc/inetd.conf
第20题:
Application of up to three access lists per protocol to a single interface.
No more than two access lists per interface.
One access list may be configured per direction for each Layer 3 protocol configured on an interface.
The maximum number allowed varies due to RAM availability in the router.
An infinite number of access lists that can be applied to an interface, from most specific to most general.
Cisco IOS allows only one access list to an interface.
第21题:
There is a mismatch in encapsulation types
The wrong type of cable is connected to the interface
The interface has been configured with the shutdown command
The interface is not receiving any keepalives
The interface needs to be configured as a DTE device
There is no encapsulation type configured
第22题:
0
1
2
3
第23题:
Units in JUNOS are always required for any interface configured with logical addresses such as IP and IPv6.
Units in JUNOS are only required when you are configuring sub-interfaces for inter-VLAN routing.
Unit numbers must match the DLCI or VCI numbers configured on the interface.
Unit 0 is the only value allowed on interfaces running HDLC, PPP, or for Ethernet interfaces not doing VLAN-tagging.
第24题:
AutoQoS can be configured from a different subinterface if the DLCI is already assigned to one subinterface
Multilink PPP (MLP) over Frame Relay must be manually configured on low speed DLCIs
for low-speed Frame Relay DLCIs with Frame Relay-to ATM interworking, the AutoQoS cannot be configured if a virtual template is already configured for the DLCI
AutoQoS can be configured on a Frame Relay DLCI only if a map class is attached to the DLCI