Defines permissions for remote machines contacting the local machine through BNU
Specifies dialer and modem types for uucp connections
Defines basic communication parameters
Assigns alternate or additional Systems, Devices and Dialers files
第1题:
A.smittty;takethedefaultsandcreatethedesiredtty
B.lsdev-Cctty;checktoseeifthedesiredttyexists,ifnotcreateusingsmitttyAddalinesimilarto;Directtty0-9600directto/etc/uucp/DevicesVerify/etc/uucp/Dialershasthefollowingline;direct
C.Installbos.net.uucpandthefirstavailablettywillbeconfiguredforusebyacusession
D.RuntheAsynchronousTerminalEmulation(ate)programanditwillconfigureattyportforacusession
第2题:
What is a function of a user role?()
第3题:
When enabling a tty port to be used for a cu session, what must be done on the system?()
第4题:
What is the purpose of /etc/uucp/Devices?()
第5题:
Which of the following commands should be used to open a tty port configured in the /etc/uucp/Devices file as: Direct tty2 - 9600 direct in debug mode, ignoring modem control signal data carrier detect (DCD)?()
第6题:
What is the purpose of a zone in JUNOS Software?()
第7题:
Create an entry for tty2 in the /etc/uucp/Devices file
Re-enter the command as cu -dml tty2
Create an entry for tty2 in the /etc/uucp/Systems file
Re-enter the command as cu -s 9600 -dh -t -l tty2
第8题:
/etc/rc.tcpip
/etc/uucp/Devices
/etc/rc.net
/etc/uucp/Dialcodes
第9题:
smit tty; take the defaults and create the desired tty
lsdev -Cc tty; check to see if the desired tty exists, if not create using smit tty Add a line similar to; Direct tty0 - 9600 direct to /etc/uucp/Devices Verify /etc/uucp/Dialers has the following line; direct
Install bos.net.uucp and the first available tty will be configured for use by a cu session
Run the Asynchronous Terminal Emulation (ate) program and it will configure a tty port for a cu session
第10题:
It defines the maximum permissible time period between missed heartbeats before a failure is detected
It defines the time period to wait to activate the network module after starting the cluster manager
It defines the period between detecting a missed heartbeat and initiating a network down, allowing thenetwork to stabilize
It defines the time period during which, after a network failure was detected, further network failures of thesame type will be ignored
第11题:
cu -l tty2
cu -dml tty2
cu -dht Direct
cu -s9600 -l tty2
第12题:
A zone defines a group of security devices with a common management.
A zone defines the geographic region in which the security device is deployed.
A zone defines a group of network segments with similar security requirements.
A zone defines a group of network segments with similar class-of-service requirements.
第13题:
A./etc/rc.tcpip
B./etc/uucp/Devices
C./etc/rc.net
D./etc/uucp/Dialcodes
第14题:
To enable a tty port to be used for a cu session what must be done to the system?()
第15题:
Which of the following has NO effect on controlling the access permissions needed to run the "date" command on the remote machine "Earth" using the following syntax?rsh Earth date()。
第16题:
When tuning a network module what is the purpose of the grace period?()
第17题:
When setting up a modem, which of the following files MUST be edited in order to configure it?()
第18题:
A system administrator has created tty2 on a serial port connection to a system. When attempting to verify the connection the following error is observed: # cu -ml tty2 cu: 0835-028 The connection failed. NO DEVICES AVAILABLE. Which of the following should be performed to correct this error?()
第19题:
The local file: /etc/.netrc
The remote file: ~/ .rhosts
The securetcpip command
The remote file: /etc/hosts.equiv
第20题:
It defines the IPsec parameters for the role.
It assigns access to resources.
It associates the user with a RADIUS server.
It defines the types of authentication methods available to the user
第21题:
It defines which devices will be sending traps.
It specifies where to send traps.
It defines the IP addresses of management systems that can access the device.
It specifies which devices can be polled for SNMP data.
第22题:
MIB
FIB
LDAP
CEF
第23题:
smit tty; take the defaults and create the desired tty
In the /etc/uucp Devices add a line similar to: Direct ttyX - 9600 direct
Install bos.net.uucp and the first available tty will be configured for use by a cu session
Run the Asynchronous Terminal Emulation (ATE) program and it will configure a tty port for a cu session
第24题:
Defines permissions for remote machines contacting the local machine through BNU
Specifies dialer and modem types for uucp connections
Defines basic communication parameters
Assigns alternate or additional Systems, Devices and Dialers files