Auto-RP
Static RP
Bootstrap Protocol
Pim Sparse-Dense mode
第1题:
A. The multicast sources must register with the RP to form the multicast distribution tree
B. An RP is required only in networks running Protocol Independent Multicast dense mode ( PIM DM)
C. The multicast receivers must register with the RP to form the multicast distribution tree
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM)
E. An RP is required only in networks running Pro tocol Independent Multicast sparse - dense mode (PIM - SDM)
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP
第2题:
当multicast启用pim sparse-mode,但是没配置auto-rp,你将用什么方法?
第3题:
The ip pim autorp listener command is used to do which of these?()
第4题:
In what PIM topology would you use MSDP within a single domain?()
第5题:
Which method should be used to dynamically elect an RP when your network is using PIM version1?()
第6题:
以下关于静态指定RP与Bootstrap 自动选举RP描述正确的有()
第7题:
When configuring a Cisco Adaptive Security Appliance in multiple context mode, which of the follow capabilities are supported?()
第8题:
Which multicast mode does Auto-RP require?()
第9题:
Auto-RP
Static RP
Bootstrap Protocol
Pim Sparse-Dense mode
第10题:
show ip pim rendez-vous
show ip rpf rp mapping
show ip pim rp mapping
show ip pim rp info
show ip pim
第11题:
PIM sparse - dense mode and PIM dense mode require an RP on the network.
PIM sparse mode and PIM dense mode require an RP on the network.
PIM sparse mode interfaces are always added to the multicast routing table in a router.
PIM sparse mode and PIM sparse - dense mode require an RP on the network.
PIM dense mode interfaces are always added to the multicast routing table in a router.
PIM sparse - dense mode acts as PIM dense mode if an RP is not known.
第12题:
Multicastis supported
Dynamic routing protocols are supported
VPN configurations are supported
Static routes are supported
第13题:
A. PIM sparse - dense mode and PIM dense mode require an RP on the network.
B. PIM sparse mode and PIM dense mode require an RP on the network.
C. PIM sparse mode interfaces are always added to the multicast routing table in a router.
D. PIM sparse mode and PIM sparse - dense mode require an RP on the network.
E. PIM dense mode interfaces are always added to the multicast routing table in a router.
F. PIM sparse - dense mode acts as PIM dense mode if an RP is not known.
第14题:
Which command can be used to check the assignment of RPs to multicast groups?()
第15题:
Which two statements are tru e about the rendezvous point (RP) in a multicast network?()
第16题:
Which of the following multicast mode does Auto-RP require?()
第17题:
Which method of dynamic RP election is non-proprietary?()
第18题:
关于RP和BSR,下列说法正确的有()。
第19题:
Which three RP election mechanisms are available in a PIM-SM domain?()
第20题:
Which three RP election mechanisms are available in a PIM-SM domain?()
第21题:
auto-RP
static RP
discovery mode
bootstrap protocol
第22题:
Static
Auto-RP
Dynamic-RP
Bootstrap router
第23题:
Static
Auto-RP
Dynamic-RP
Bootstrap router
Anycast-RP
第24题:
enable a Cisco router to passively listen to Auto-RP packets without the router actively sending or forwarding any of the packets
allow Auto-RP packets in groups 224.0.1.39 and 224.0.1.40 to be flooded in dense mode out interfaces configured with the ip pim sparse-mode command
enable the use of Auto-RP on a router
configure the router as an Auto-RP mapping agent