0
1
5
100
第1题:
A.voice over IP
B.wholesale services
C.IP quality of service
D.SNMP management
第2题:
A.The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.
B.The HSRP default timers are a 3 second hello interval and a 10 second dead interval.
C.HSRP supports only clear-text authentication.
D.The HSRP virtual IP address must be on a different subnet than the routers‘ interfaces on the same LAN.
E.The HSRP virtual IP address must be the same as one of the router‘s interface addresses on the LAN.
F.HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.
第3题:
Which two factors determine the recommended maximum number of virtual interfaces on a Cisco UCSsystem?()
第4题:
If the default VDC is configured to limit resources to a specific module type, what happens when a module that does not match the resource type is installed?()
第5题:
Your ERX router is supporting 100 virtual routers.A specific line module supports IP interfaces in 5 virtual routers.How many routing tables are maintained on that module?()
第6题:
Where does Layer2 de-encapsulation occur on the ERX Edge Router?()
第7题:
VRRP的全称是:()
第8题:
What is the maximum number of NET addresses supported on a virtual router?()
第9题:
0
1
5
100
第10题:
The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.
The HSRP default timers are a 3 second hello interval and a 10 second dead interval.
HSRP supports only clear-text authentication.
The HSRP virtual IP address must be on a different subnet than the routers' interfaces on the same LAN.
The HSRP virtual IP address must be the same as one of the router's interface addresses on the LAN.
HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.
第11题:
on the SRP
on the I/O adapter
on the egress line module
on the ingress line module
第12题:
The module is powered up, and interfaces are in an admin down state.
The module is denied power, and a syslog message is generated.
The module is powered up, and interfaces are allocated to VDC0.
The module is powered up, and interfaces are allocated to VDC100.
第13题:
A. Administratively shut down the interface.
B. Physically secure the interface.
C. Create an access list and apply it to the virtual terminal interfaces with the access-group command.
D. Configure a virtual terminal password and login process.
E. Enter an access list and apply it to the virtual terminal interfaces using the access-class command.
第14题:
A.Virtual Routing Redundancy Protocol
B.Virtual Router Redundancy Protocol
C.Virtual Redundancy Router Protocol
D.Virtual Redundancy Routing Protocol
第15题:
You wish to increase the security of all of the routers within your network. What can be done to secure the virtual terminal interfaces on a router?()
第16题:
Your ERX Edge Router is constantly going to a boot## prompt. What is the most likely cause for this condition?()
第17题:
Which two parameters are virtual router specific?()
第18题:
Your ERX router is supporting 100 virtual routers. A specific line module supports IP interfaces in 5 virtual routers.How many routing tables are maintained on that module?()
第19题:
You wish to limit telnet access into your Cisco router to only a single host. In order to accomplish this, access list 1 has been written to allow host 172.16.1.224 access to the router vty lines. What command would assign this access- list to the Virtual Terminal Lines?()
第20题:
Which service does the ERX Edge Router support with a virtual router?( )
第21题:
0
1
5
100
第22题:
32
128
256
1000
第23题:
bad SRP
low voltage
bad mid-plane
corrupted flash
bad line module
第24题:
the number of computer blades in the system
the number of interfaces sharing the uplinks
the driver version on the OS running on the computer blade
the number of uplinks between I/O Module and Fabric Interconnect