set protocols setospf area 0 set interface so-0/0/0.100
set protocols ospf area 0 interface so-0/0/0.100
edit protocols ospf interface so-0/0/0.100
edit protocols ospf area 0 set interface so-0/0/0.100
第1题:
A. Each OSPF area requires a loopback interface to be configured.
B. Areas may be assigned any number from 0 to 65535.
C. Area 0 is called the backbone area.
D. Hierarchical OSPF networks do not require multiple areas.
E. Multiple OSPF areas must connect to area 0.
F. Single area OSPF networks must be configured in area 1.
第2题:
You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? ()
第3题:
Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 in JUNOS software?()
第4题:
You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100.Which two achieve this result?()
第5题:
Which of the following are characteristics of OSPF areas?()
第6题:
You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?()
第7题:
Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 inJUNOS software?()
第8题:
set protocols set ospf area 0 set interface so-0/0/0.100
set protocols ospf area 0 interface so-0/0/0.100
edit protocols ospf interface so-0/0/0.100
edit protocols ospf area 0 set interface so-0/0/0.100
第9题:
set interfaces ge-0/3/0 unit 0 metric 10
set protocols ospf reference-bandwidth 10g
set interfaces ge-0/3/0 unit bandwidth 10g
set protocols ospf area 0 interface ge-0/3/0 metric 10
set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
第10题:
set protocols set ospf area 0 set interface so-0/0/0.100
set protocols ospf area 0 interface so-0/0/0.100
edit protocols ospf interface so-0/0/0.100
edit protocols ospf area 0 set interface so-0/0/0.100
第11题:
set interfaces ge-0/3/0 unit 0 metric 10
set protocols ospf reference-bandwidth 10g
set interfaces ge-0/3/0 unit 0 bandwidth 10g
set protocols ospf area 0 interface ge-0/3/0 metric 10
set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
第12题:
set protocols setospf area 0 set interface so-0/0/0.100
set protocols ospf area 0 interface so-0/0/0.100
edit protocols ospf interface so-0/0/0.100
edit protocols ospf area 0 set interface so-0/0/0.100
第13题:
第14题:
OSPF routing uses the concept of areas. What are the characteristics of OSPF areas?()
第15题:
You are the top of hierarchy and must configure OSPF on inteface so-0/0/0 unit 100. Which two achieve this result?()
第16题:
You want to allow your device to establish OSPF adjacencies with a neighboring device connected to interface ge-0/0/3.0. Interface ge-0/0/3.0 is a member of the HR zone.Under which configuration hierarchy must you permit OSPF traffic?()
第17题:
You accidentally configured interface so-0/0/0.0 with /32 instead of /30. Which two solutions could you use to correct this configuration?()
第18题:
You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?()
第19题:
[edit interfaces so-0/0/0.0] user@router# replace family inetaddress /32 with /30
[edit interfaces so-0/0/0.0] user@router# rename family inetaddress /32 to address /30
[edit] user@router# replace interface so-0/0/0.0 family inetaddress /32 with address /30
[edit interfaces so-0/0/0.0] user@router# delete family inet address user@router# set family inetaddress /30
第20题:
All OSPF networks require the use of multiple areas
Multiple OSPF areas must connect to area 0
Single area OSPF networks must be configured in area 1
Areas can be assigned any number from 0 to 63535
Area 0 is called the backbone area
Each OSPF area need to be configured with a loopback interface
第21题:
Each OSPF area requires a loopback interface to be configured.
Areas may be assigned any number from 0 to 65535.
Area 0 is called the backbone area.
Hierarchical OSPF networks do not require multiple areas.
Multiple OSPF areas must connect to area 0.
Single area OSPF networks must be configured in area 1.
第22题:
Hierarchical OSPF networks need to be in one area
Multiple OSPF areas must connect to area 0
Single area OSPF networks must be configured in area 1
Areas can be assigned any number from 0 to 63535
Area 0 is called the backbone area
Each OSPF area need to be configured with a loopback interface
第23题:
set protocols isis inet6
set routing-options router-id router-id
set protocols ospf3 area 0 interface all
set interface fe-0/0/1 unit 0 family inet6
set routing-options ipv6-router-id router-id