port number
PCI slot number
channel number
virtual PIC number
第1题:
Every host and router on the Internet has an IP address, which encodes its(12).
A.host number
B.network number
C.host number and socket
D.host number and network number
第2题:
Every host and muter on the Internet has an IP address,which encodes its(69).
A.host number
B.host number and socket
C.network number
D.host number and network number
第3题:
A. The broadcast address, and AS number
B. The network number and AS number
C. EIGRP routing, network number and passive interface
D. EIGRP routing, network number, and AS
第4题:
In our office, the women()the men 3 to 1.
第5题:
When building a NIC team (virtual port channel) between a host and a pair of Cisco Nexus 5000 Series Switches that will carry FCoE traffic, what is the maximum number of physical links that can exist in the team?()
第6题:
What parameters must you specify when you enable EIGRP routing?()
第7题:
What does the number one 1 represent for interface fe-0/0/1?()
第8题:
A standard access control list has been configured on a router and applied to interface Serial 0 in anoutbound direction. No ACL is applied to Interface Serial 1 on the same router. What will happen whentraffic being filtered by the access list does not match the configured ACL statements for Serial 0?()
第9题:
A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?()
第10题:
show interface 5/0:4
show interface 5/0:4/1
show controllers t3 5/0:4
show controllers t3 5/0:4/1
第11题:
the port-channel 1 interface
the highest number member interface
all member interfaces
the lowest number member interface
第12题:
The traffic is dropped
The resulting action is determined by the destination IP address
The source IP address is checked,and,if a match is not found, traffic is routed out interface Serial 1
The resulting action is determined by the destination IP address and port number
第13题:
有以下程序: main() { char k: int i; for(i=1:i<3;i++) { scanf("%c",&k); switch(k) { case'0':printf("another\n"); case'1':printf("number\n"); } } } 程序运行时,从键盘输入:01<回车>,程序执行后的输出结果是 ______。
A.another number
B.another number another
C.another number number
D.number number
第14题:
有以下程序 main() { char k;int i; for(i=1;i<3;i++) { scanf("%c",&k); switch(k) { case'0':printf("another\n"); case'1':printf("number\n"); } } } 程序运行时,从键盘输入:01<回车>,程序执行后的输出结果是
A.another number anothor
B.another number number
C.another number
D.number number
第15题:
A.the port-channel 1 interface
B.the highest number member interface
C.all member interfaces
D.the lowest number member interface
第16题:
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-treetopology?()
第17题:
指定逻辑通道备份主接口使用的命令是()。
第18题:
You are asked to change the cable on interface ge-0/2/1.Which statement is correct?()
第19题:
哪一个列名是有效的()
第20题:
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology?()
第21题:
Which command displays the results of a loopback test you executed on a CT3 line module in slot 5,port 0,t1 number 4?()
第22题:
port number
PCI slot number
channel number
virtual PIC number
第23题:
1
2
4
5
16
第24题:
The cable is found on slot 2, port 0, and FPC 1.
The cable is found on FPC 0, slot 1, and port 2.
The cable is found on port 1, slot 0, and FPC 2.
The cable is found on slot 2, port 1, and FPC 0.