单选题Which multicast address does RIPv2 use for route updates by default?()A 224.0.0.2B 224.0.0.5C 224.0.0.9D 255.255.255.255

题目
单选题
Which multicast address does RIPv2 use for route updates by default?()
A

224.0.0.2

B

224.0.0.5

C

224.0.0.9

D

255.255.255.255


相似考题
更多“单选题Which multicast address does RIPv2 use for route updates by default?()A 224.0.0.2B 224.0.0.5C 224.0.0.9D 255.255.255.255”相关问题
  • 第1题:

    As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?()

    A. TestKSwitch(config)# ip route-default 192.168.1.115

    B. TestKSwitch(config)# ip default-gateway 192.168.1.115

    C. TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0

    D. TestKSwitch(config)# ip default-network 192.168.1.115


    参考答案:B

  • 第2题:

    Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()

    A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0

    B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0

    C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0

    D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0

    E. Router(config)# ip route any any e0


    参考答案:D

  • 第3题:

    Which configuration command assigns a host route to the CPE workstation address of 192.168.10.1 in a Bridged 1483 network?()

    • A、ip route 192.168.10.1 255.255.255.255 atm 6/2.1
    • B、ip route 192.168.10.1 255.255.255.252 atm 6/2.1
    • C、add route 192.168.10.1 255.255.255.252 atm 6/2.1
    • D、add route 192.168.10.1 255.255.255.255 atm 6/2.1

    正确答案:A

  • 第4题:

    Which three IP multicast group concepts are true?()

    • A、If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.
    • B、A router does not have to be a member of a multicast group to receive multicast data.
    • C、A router must be a member of a multicast group to send to the group.
    • D、A router does not have to be a member of a multicast group to send to the group.
    • E、If a packet is sent to a multicast group address, all members of the multicast group will rece ive it.
    • F、A router must be a member of a multicast group to receive multicast data.

    正确答案:D,E,F

  • 第5题:

    Which OSPF LSA type does an ASBR use to originate a default route into an area? ()

    • A、 LSA 1
    • B、 LSA 3
    • C、 LSA 4
    • D、 LSA 5
    • E、 LSA 7

    正确答案:D

  • 第6题:

    Which three statements are true about EIGRP route summarization?()

    • A、When manual summarization is configured, the router immediately creates a route that points to null0 interface
    • B、Manual route summarization  is configured in router configuration mode when the router is configured for EIGRP routing
    • C、Manual route summarization is configured on the interface
    • D、The ip summary - address eigrp command generates a default route with an administrative distance  of 5
    • E、When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routes
    • F、The ip summary - address eigrp command generates a default route with an administrative distance of 90

    正确答案:A,C,D

  • 第7题:

    Which multicast address does RIPv2 use for route updates by default?()

    • A、224.0.0.2
    • B、224.0.0.5
    • C、224.0.0.9
    • D、255.255.255.255

    正确答案:C

  • 第8题:

    单选题
    What is the difference between the IPv6 addresses ::/0 and :: /128? ()
    A

    ::/0 is the default route, and ::/128 is the unspecified address.

    B

    ::/0 is the unicast address, and ::/128 is the anycast address.

    C

    ::/0 is the anycast address, and ::/128 is the multicast address.

    D

    ::/0 is the unicast address, and ::/12 8 is the multicast address.

    E

    ::/0 is the unspecified address, and ::/128 is the multicast address.

    F

    ::/0 is the anycast address, and ::/128 is the default address.


    正确答案: E
    解析: 暂无解析

  • 第9题:

    多选题
    Which of the commands below can you use to configure a default route?()
    A

    TK1(config)# ip route 0.0.0.0 0.0.0.0 E0

    B

    TK1(config)# ip route 0.0.0.0 255.255.255.255 S0

    C

    TK1(config-interface)# ip route 255.255.255.255 0.0.0.0 192.168.1.21

    D

    TK1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.21

    E

    TK1(config)# ip route 0.0.0.0 192.168.1.21 255.255.255.255

    F

    TK1# ip default-network 0.0.0.0 192.168.1.21 255.255.255.255


    正确答案: A,D
    解析: 暂无解析

  • 第10题:

    多选题
    RIPv2 differs from RIPv1 in that:()
    A

    it uses multicast address 224.0.0.10,instead of broadcast

    B

    it uses multicast address 224.0.0.9,instead of broadcast

    C

    it can use either multicast or broadcast addresses,instead of just broadcast

    D

    it sends incremental updates,instead of periodic updates

    E

    it is classless,instead of classful

    F

    it supports authentication,and RIPv1 does not


    正确答案: E,A
    解析: 暂无解析

  • 第11题:

    单选题
    What is the difference between the IPv6 addresses ::/0 and ::/128?()
    A

    ::/0 is the unspecified address, and ::/128 is the multicast address

    B

    ::/0 is the unicast address, and ::/128 is the anycast address

    C

    ::/0 is the unicast address, and ::/128 is the multicast address

    D

    ::/0 is the anycast address, and ::/128 is the multicast address

    E

    ::/0 is the default route, and ::/128 is the unspecified address

    F

    ::/0 is the anycast address, and ::/128 is the default address


    正确答案: E
    解析: 暂无解析

  • 第12题:

    单选题
    Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()
    A

    Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0

    B

    Router(config)# ip route 0.0.0.0 255.255.255.255 s0

    C

    Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0

    D

    Router(config)# ip route 0.0.0.0 0.0.0.0 s0

    E

    Router(config)# ip route any any e0


    正确答案: B
    解析: 暂无解析

  • 第13题:

    You have been asked to configure a default route. Which of the IOS commands mentioned below will accomplish this task?()

    A. LTD(config)# ip route 0.0.0.0 0.0.0.0 192.168.15.36

    B. LTD(config)# ip route 0.0.0.0 192.168.15.36 255.255.255.255

    C. LTD# ip default-network 0.0.0.0 192.168.15.36 255.255.255.255

    D. LTD(config)# ip route 0.0.0.0 0.0.0.0 E0

    E. LTD(config)# ip route 0.0.0.0 255.255.255.255 S0

    F. LTD(config-router)# ip route 255.255.255.255 0.0.0.0 192.168.15.36


    参考答案:A, D

  • 第14题:

    Which of the commands below can you use to configure a default route?()

    A. TK1(config)# ip route 0.0.0.0 0.0.0.0 E0

    B. TK1(config)# ip route 0.0.0.0 255.255.255.255 S0

    C. TK1(config-interface)# ip route 255.255.255.255 0.0.0.0 192.168.1.21

    D. TK1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.21

    E. TK1(config)# ip route 0.0.0.0 192.168.1.21 255.255.255.255

    F. TK1# ip default-network 0.0.0.0 192.168.1.21 255.255.255.255


    参考答案:A, D

  • 第15题:

    Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()

    • A、Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0
    • B、Router(config)# ip route 0.0.0.0 255.255.255.255 s0
    • C、Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0
    • D、Router(config)# ip route 0.0.0.0 0.0.0.0 s0
    • E、Router(config)# ip route any any e0

    正确答案:D

  • 第16题:

    What is the difference between the IPv6 addresses ::/0 and ::/128?()

    • A、::/0 is the unspecified address, and ::/128 is the multicast address
    • B、::/0 is the unicast address, and ::/128 is the anycast address
    • C、::/0 is the unicast address, and ::/128 is the multicast address
    • D、::/0 is the anycast address, and ::/128 is the multicast address
    • E、::/0 is the default route, and ::/128 is the unspecified address
    • F、::/0 is the anycast address, and ::/128 is the default address

    正确答案:E

  • 第17题:

    RIPv2 differs from RIPv1 in that:()

    • A、it uses multicast address 224.0.0.10,instead of broadcast
    • B、it uses multicast address 224.0.0.9,instead of broadcast
    • C、it can use either multicast or broadcast addresses,instead of just broadcast
    • D、it sends incremental updates,instead of periodic updates
    • E、it is classless,instead of classful
    • F、it supports authentication,and RIPv1 does not

    正确答案:B,E,F

  • 第18题:

    Which two statements are true about the primary address on an interface? ()

    • A、It is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interface
    • B、You use the primary address when you have multiple IP addresses belonging to the same subnet on the same inteface
    • C、It can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interface
    • D、By default, the primary address on an interface is selected as the nmerically highest local address configured on the interface

    正确答案:A,C

  • 第19题:

    单选题
    Which multicast address does RIPv2 use for route updates by default?()
    A

    224.0.0.2

    B

    224.0.0.5

    C

    224.0.0.9

    D

    255.255.255.255


    正确答案: B
    解析: 暂无解析

  • 第20题:

    多选题
    You have been asked to configure a default route. Which of the IOS commands mentioned below will accomplish this task?()
    A

    LTD(config)# ip route 0.0.0.0 0.0.0.0 192.168.15.36

    B

    LTD(config)# ip route 0.0.0.0 192.168.15.36 255.255.255.255

    C

    LTD# ip default-network 0.0.0.0 192.168.15.36 255.255.255.255

    D

    LTD(config)# ip route 0.0.0.0 0.0.0.0 E0

    E

    LTD(config)# ip route 0.0.0.0 255.255.255.255 S0

    F

    LTD(config-router)# ip route 255.255.255.255 0.0.0.0 192.168.15.36


    正确答案: A,D
    解析: 暂无解析

  • 第21题:

    单选题
    Which OSPF LSA type does an ASBR use to originate a default route into an area? ()
    A

     LSA 1

    B

     LSA 3

    C

     LSA 4

    D

     LSA 5

    E

     LSA 7


    正确答案: D
    解析: 暂无解析

  • 第22题:

    单选题
    Which OSPF LSA type does an ASBR use to originate a default route into an area?()
    A

    LSA 1

    B

    LSA 3

    C

    LSA 4

    D

    LSA 5

    E

    LSA 7


    正确答案: D
    解析: 暂无解析

  • 第23题:

    单选题
    As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?()
    A

    TestKSwitch(config)# ip route-default 192.168.1.115

    B

    TestKSwitch(config)# ip default-gateway 192.168.1.115

    C

    TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0

    D

    TestKSwitch(config)# ip default-network 192.168.1.115


    正确答案: D
    解析: 暂无解析

  • 第24题:

    单选题
    Which configuration command assigns a host route to the CPE workstation address of 192.168.10.1 in a Bridged 1483 network?()
    A

    ip route 192.168.10.1 255.255.255.255 atm 6/2.1

    B

    ip route 192.168.10.1 255.255.255.252 atm 6/2.1

    C

    add route 192.168.10.1 255.255.255.252 atm 6/2.1

    D

    add route 192.168.10.1 255.255.255.255 atm 6/2.1


    正确答案: C
    解析: 暂无解析