configuring a second network card with a different IP address
replacing the existing 100 Mbps NIC with a gigabit Ethernet NIC
using adapter teaming and configuring the second network card with the same IP address as the first network card
installing a dual-port network card that can handle the future growth and setting one NIC to 10 Mbps and one NIC to 100 Mbps
第1题:
A second network card in a server that activates if the primary card fails is an example of which of the following network performance optimization?()
第2题:
A customer wants to increase the performance of an existing server. They are running a very network intensive application and feel that increasing the bandwidth to the network will fix their problem. They are running two 24-port autosensing 10/100 hubs, tied together with a standard Ethernet crossover cable in port 24. The server is running IPX. After adding a second network card and plugging one card into each hub, they have not seen any performance improvement. Which two are likely reasons why implementing network adapter teaming has not improved performance?()
第3题:
An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot. Which of the following is the FIRST thing the administrator should check?()
第4题:
You are the administrator of a small server based network. While installing Windows 2000 Professional on your computer, you configure the network adapter card for each computer to use TCP/IP and assign static IP setting information. During installation the setup detects and installs the 10/100 MBPS UTP only network adepter card on computers 6 & 8 and 10 MBPS/UTP combination adapter card on the other 7 computers. You accept the default settings for the network adapter card and finish installing the network adapter card. All computers are connected to 10/100 switch that has category 5 UTP cabling. After installation you find that computer 6 and 8 can communicate with each other. You want all 9 computers on your network to be able to communicate with each other. What should you do?()
第5题:
Your Company upgrades its network to 100 Mbps. You remove the old network adapter and install a new 10/100 Mbps network adapter into a Windows 2000 Professional computer. You configure the TCP/IP protocol settings to be the same as they were for the previously installed network adapter. When you restart eh computer, however, you cannot access the network. You try to ping your network adapter’s TCP/IP address locally. You receive the following error message. “Request timed out.” Next, you try to ping 127.0.0.1 and receive the same error message. What must you do?()
第6题:
Recently traffic to the company web server has more than doubled, resulting in slower response times from the server. An administrator has decided to add a second, identical 10/100/1000 NIC to the server. The server is presently connected to a 10/100/1000 switch, with four open ports on the switch. Which of the following is the BEST solution to speed up web traffic?()
第7题:
configuring a second network card with a different IP address
replacing the existing 100 Mbps NIC with a gigabit Ethernet NIC
using adapter teaming and configuring the second network card with the same IP address as the first network card
installing a dual-port network card that can handle the future growth and setting one NIC to 10 Mbps and one NIC to 100 Mbps
第8题:
Load balancing
QoS
High availability
Fault tolerance
第9题:
Adapter teaming is designed to work with switches.
Adapter teaming only functions with gigabit network cards.
Adapter teaming only provides fault tolerance, not additional bandwidth.
Adapter teaming only works with IPX when using switches and network cards with special features that support teaming.
第10题:
To achieve the goal, the Connection should be set to None for the network interface card.
To achieve the goal, the Microsoft Loopback Adapter should be installed.
To achieve the goal, a new Virtual Network should be created.
To achieve the goal, Internet Connection Sharing (ICS) should be enabled.
第11题:
Upgrade the network switches to 10Gb speed.
Install a dual port gigabit Ethernet adapter and configure adapter load balancing teaming with the onboard adapters.
Install one extra adapter to team with the internal adapter and configure adapter failover.
Install two additional NICs and configure adapter load balancing teaming with the onboard adapters.
第12题:
A single adapter network using the Network Interface Card in each node
A single adapter network using persistent addresses on the Network Interface Card in each node
A dual adapter network using the internal Ethernet adapters as an non-service interface with IPAT via IP Replacement.
EtherChannel high availability for the network connections with HACMP cascading resource groups for data and application fallover
第13题:
A company plans to upgrade a network server. Before proceeding with the upgrade, the HCL (Hardware Compatibility List) and hardware is checked and necessary backups and documentation are made. The existing 512 MB of SDRAM is replaced with 1024 MB. The 10 Mbps network card is replaced with a 10/100 PCI network card. When the server restarts, beeps sound and the server does not pass the POST. Which of the following is the MOST likely cause of the problem?()
第14题:
An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot. Which of the following is the FIRST thing the administrator should check?()
第15题:
Company.com has I/O slot constraints on two nodes that are going to be configured in an HACMP cluster. There is room for only one Network Interface Card in each node,in addition to the built-in Ethernet port on the system planer. The best HACMP configuration for these servers is to implement:()
第16题:
You have a 10Mbps network card in your computer. You install a 100Mbps network card on your computer and restart the computer. The 100Mbps card in not working due to a conflict with the10Mbps card. You want only the 100Mbps card to be active. What should you do to disable the10 Mbps network adapter?()
第17题:
You work as the IT professional in an international company which is named Wiikigo. You are experiencedin implementing and administering a network operating system. You are specialized in deploying servers,configuring Windows Server 2008 Terminal services and network application services, and configuring aweb services infrastructure. There is a server in your company. Windows Server 2008 is run by the serverand the server has the Hyper-V server role installed.A new virtual machine is created. You are required to configure the virtual machine, and the requirements listed below should be satisfied.First, network communications should be permitted between the virtual machine and the host system.Second, communications should be prevented with other network servers. To achieve the goal,which action should be performed first?()
第18题:
Default gateway
The ports on the switch
Port security on the server's switch port
Ethernet cable
第19题:
Free up more ports on the switch
Enable server load balancing
Move the second network adapter to a new subnet
Enable network adapter teaming
第20题:
Remove the 100MB Ethernet adapter driver by using device manager.
Remove the drivers for both Ethernet adapters cards by using device manager.
Install the 100MB Ethernet adapter in different PC card slots.
Disable the device drivers for the 10Mb card using by using Device Manager.
第21题:
Default gateway
The ports on the switch
Port security on the servers switch port
Ethernet cable
第22题:
Configure the 10/100 switch to transfer only at the 100 MBPS rate.
Configure 10/100 MBPS network adapter card to switch all the computers at 10 MBPS rate.
Change the combination network adapter card to use the BNC transceiver setting.
Change the combination network adapter card to use the UTP transceiver setting.
第23题:
The memory is not seated correctly.
The network card is not configured correctly.
The server does not support 1024 MB of memory.
Master SDRAM ECC needs to be enabled in the CMOS.
第24题:
Create two virtual adapters on the client, each one from a separate Virtual IO Server
Enable dead gateway detection on the client so that the network traffic can be rerouted
Have a spare network card on standby in the client in case the Virtual IO Server goes down
Create an etherchannel adapter on the client using one Virtual Ethernet adapter from two separate Virtual IO Servers