The WAN link is down.
IPSec is enabled on the WX.
Traceroute is enabled for compression.
The network is configured using static routes.
The local and remote cables are accidentally swapped.
第1题:
Which three IP multicast address related statements are true? (Choose three.) ()
第2题:
Which three circumstances would prevent traceroute from displaying the WAN IP addresses? ()(Choose three)
第3题:
Which three methods would help prevent critical network-traffic packet loss on high speed serial interfaces?()
第4题:
Which three causes could prevent a host from getting an IPv6 address with stateless autoconfiguration?()
第5题:
Receive port: Enabled, Transmit port: Enabled
Receive port: Enabled, Transmit port: Desired
Receive port: Enabled, Transmit port: Disabled
Receive port: Disabled, Transmit port: Desired
Receive port: Desired, Transmit port: Desired
第6题:
policy routing
increase link capacity
WRED
CBWFQ
LFI
WFQ
第7题:
over-subscribed
under-subscribed
dedicated circuits
nondedicated circuits
第8题:
Multicast addresses 224.0.1.0 through 238.255.255.255 are called globally scoped addresses. They are used to multicast data between organizations and across the Internet
The multicast address 224.0.0.1 is a globally scoped address that has been reserved for the Network Time Protocol (NTP) by the IANA
Multicast addresses 239.0.0.0 through 239.255.255.255 are called limited scope addresses. They are constrained to a local group or organization
Multicast addresses 224.0.0.5 and 224.0.0.6 are limited scoped addresses that have been reserved for OSPF
Multicast addresses 224.0.0.0 through 224.0.0.255 are used for network protocols on local LAN segments. Because they are always transmitted with a Time to Live (TTL) of 1, they are never forwarded by a router
第9题:
Excluded traffic is not accelerated.
Excluded traffic is only compressed.
Source/destination filter applies to all traffic sent from LAN to WAN.
Source/destination filters work in packet interception mode using RIPv2.
第10题:
policy routing
increase link capacity
WRED
CBWFQ
LFI
WFQ
第11题:
The ip classless command is enabled by default in recent versions of IOS.
The ip classless command should only be enabled when static routing is being used instead of a routing protocol.
The ip classless command should be enabled by the network administrator whenever RIPv1 or IGRP is being used.
The ip classless command should be enabled by the network administrator whenever OSPF, RIPv2, or EIGRP is being used.
第12题:
HDLC
Ethernet
Token Ring
PPP
FDDI
Frame Relay
第13题:
An administrator is concerned about users utilizing the company's wireless signal with their personal laptops. Which of the following is the BEST method to use to prevent unauthorized devices from using the company's wireless network?()
第14题:
Which two statements are true when source/destination filters are enabled? ()(Choose two.)
第15题:
Which three Layer 2 encapsulation types would be used on a WAN rather than a LAN? (Choose three.)()
第16题:
Which three methods would help prevent critical network-traffic packet loss on high speed interfaces?()
第17题:
Reboot the device.
Reapply the license key.
Save the current configuration.
Load the image using FTP, TFTP, or from the local disk.
Back up the configration using FTP, TFTP, or to the local disk
第18题:
HDLC
Ethernet
Token Ring
PPP
FDDI
Frame Relay
第19题:
The switch name must match the workgroup name of the local network.
The switch must be configured with an IP address and default gateway.
The remote workstations must have access to the management VLAN of the switch.
CDP must be enabled on the switch so that it can be located by other devices on the network.
第20题:
The interface must be configured as a Multilink PPP interface
The correct bandwidth should be configured on the interface
A QoS policy must not be currently attached to the interface
CEF must be enabled
AutoQoS must be enabled globally before it can be enabled on the interface
An IP address must be configured on the interface if its speed is equal to or less than 768 kbps
第21题:
The autoconfig command is missing from the router interface.
IPv6 multicast routing is not enabled on the router interface.
IPv6 unicast routing is not enabled on the router interface.
The router interface is configured with a /63 mask.
The router interface is configured with a /65 mask.
第22题:
The WAN link is down.
IPSec is enabled on the WX.
Traceroute is enabled for compression.
The network is configured using static routes.
The local and remote cables are accidentally swapped.
第23题:
The interface you configured for AutoQoS is set to half-duplex
AutoQoS was configured on only one end of the link
The interface you configured for AutoQoS has no IP address
The interface’s bandwidth is not correctly configured
CEF is not enabled on the interface
You enabled AutoQoS on the interface but forgot to enable globally first
第24题:
Multicast addresses 224.0.0.0 through 224.0.0.255 are always forwarded because they are transmitted with Time to Live (TTL) greater than 1.
Multicast addresses 224.0.0.5 and 224.0.0.6 are source multicast addresses for OSPF routers.
Multicast addresses 224.0.0.13 and 224.0.0.22 are reserved link-local addresses used by PIMv2 and IGMPv3.
Because they would map to overlapping IP multicast MAC addresses, multicast addresses 224.0.1.1 and 238.1.1.1 could not be used together.
Multicast address 224.0.1.1 has been reserved for the Network Time Protocol (NTP) by the IANA
The administratively scoped multicast addresses 239.0.0.0 through 239.255.255.255 are similar in purpose to RFC 1918 private unicast addresses.