多选题Youe just configured the network interface on You？e just configured the network interface on systemA and the following information is displayed pertaining to systemA’s network interface： You have been instructed to change the name of this system to sys

第1题：

第2题：

You have just created a new VLAN on your network for inter-VLAN routing.  What is one step that you should include in your VLAN-based implementation and verification plan？（）

• A、Verify that different native VLANs exist between two switches for security purposes.
• B、Verify that the switch is configured to allow for trunking on the switch ports.
• C、Verify that each switch port has the proper IP address space assigned to it for the new VLAN. 
• D、Verify that the VLAN virtual interface has been correctly created and enabled.

第3题：

You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）

• A、EIGRP for IPv6 is directly configured on the interfaces over which it runs.
• B、EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.
• C、There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.
• D、There is no network statement configuration in EIGRP for IPv6.
• E、When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.
• F、When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive

第4题：

Company.com wishes to use HACMP on two IBM eServer pSeries servers. During the planning  session， it was decided to use the native serial ports s1 or s2 for a non-IP heartbeat network.  What should be done to ensure the serial network will function with HACMP heartbeats？（）  

• A、 Use either s1 or s2 port configured as a TTY interface with a NULL Modem cable.
• B、 Use the s2 serial port on each system configured as a TTY interface with a NULL modem cable.
• C、 Use the s1 port on each system configured as a TTY interface with a standard serial modemcable.
• D、 Verify with IBM support which native serial ports for the server model can be used for HACM  pheartbeats.

第5题：

The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）

• A、The Gallant router has the wrong LMI type configured
• B、Inverse ARP is providing the wrong PVC information to the Gallant router
• C、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
• D、The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
• E、The IP address on the serial interface of the Attalla router is configured incorrectly

第6题：

Company.com has I/O slot constraints on two nodes that are going to be configured in an  HACMP cluster. There is room for only one Network Interface Card in each node，in addition to the built-in Ethernet port on the system planer.  The best HACMP configuration for these servers is to implement：（）  

• A、 A single adapter network using the Network Interface Card in each node
• B、 A single adapter network using persistent addresses on the Network Interface Card in each node
• C、 A dual adapter network using the internal Ethernet adapters as an non-service interface with IPAT via IP Replacement.
• D、 EtherChannel high availability for the network connections with HACMP cascading resource groups for data and application fallover

第7题：

You've configured an interface with an IP address and commited the change. You then commited a change that added an exception in a firewall filter to allow this network through the filter. You realize that this work was done on the wrong router. How do you undo all these changes?（）

• A、rollback 2
• B、rollback 1
• C、rollback 0
• D、rollback 3

第8题：

You configured an interface with an IP address and committed the change. You then committed a change that added an exception in a firewall filter to allow this network through the filter. You realize that this work was done on the wrong router. How do you undo all these changes?（）

• A、rollback 2
• B、rollback 1
• C、rollback 0
• D、rollback 3

第9题：

第10题：

第11题：

第12题：

第13题：

第14题：

You work as a network engineer at TestKing.com. TestKing users have noticed extremely slow network performance, intermittent connectivity, and connection loss. After entering the show interfaces command, you notice that the Ethernet interface is configured as 100 Mbps full-duplex and that there is evidence of late collisions. What could be the cause of this problem?（）

• A、duplex mismatch
• B、a routing loop
• C、trunking mode mismatch
• D、improperly configured root bridge
• E、improperly configured static VLAN

第15题：

You are using AutoQoS Enterprise and realize that the results are not what you expected. Whichof the following are possible reasons for AutoQoS not functioning correctly？（Choose all thatapply.）（）

• A、The interface you configured for AutoQoS is set to half-duplex
• B、AutoQoS was configured on only one end of the link
• C、The interface you configured for AutoQoS has no IP address
• D、The interface’s bandwidth is not correctly configured
• E、CEF is not enabled on the interface
• F、You enabled AutoQoS on the interface but forgot to enable globally first

第16题：

You have a server named Server2 that runs Windows Server 2003 Service Pack 2 (SP2). The server has two network connections named Local Area Connection and Internet Connection.You configure network address translation (NAT) on Server2 as shown in the exhibit. (Click the Exhibit button.) You configure all client computers to use Server2 as their default gateway.Users report that they cannot connect to the Internet. You successfully connect to the Internet from Server2.You need to ensure that client computers can access Internet resources.  What should you do?（）

• A、Change the Internet Connection interface type to Basic firewall only. 
• B、Change the Internet Connection interface type to Private interface connected to private network. 
• C、Add Local Area Connection as a new interface for the NAT protocol and set the interface as a Public interface connected to the Internet. 
• D、Add Local Area Connection as a new interface for the NAT protocol and set the new interface as a Private interface connected to private network.

第17题：

A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?（）

• A、an OSPF update for network 192.168.0.0/16
• B、a static router to network 192.168.10.0/24
• C、a static router to network 192.168.10.0/24 with a local serial interface configured as the next hop
• D、a RIP update for network 192.168.10.0/24
• E、a directly connected interface with an address of 192.168.10.254/24
• F、a default route with a next hop address of 192.168.10.1

第18题：

An AIX server has 2 network interfaces and the system administrator wants to enable the users on the locally configured network interface to be able to connect to systems configured on the global network interface.  How is it accomplished？（）

• A、Enable routed on the server
• B、Enable gated on the server
• C、Enable ipforwarding on the server
• D、Set network options back to default

第19题：

You have a firewall filter applied in an inbound direction on a customer interface. You would like this filter to protect your network from a spoofed denial of service attack. Which action should be configured to accomplish your goal?（）

• A、then reject
• B、then discard
• C、then next filter
• D、then silent-drop

第20题：

Your network contains a single Active Directory domain. All servers run Windows Server 2008 R2. A DHCP server is deployed on the network and configured to provide IPv6 prefixes.You need to ensure that when you monitor network traffic,you see the interface identifiers derived from the Extended Unique Identifier (EUI)-64 address.Which command should you run?（）

• A、netsh.exe interface ipv6 set global addressmaskreply=disabled
• B、netsh.exe interface ipv6 set global dhcpmediasense=enabled
• C、netsh.exe interface ipv6 set global randomizeidentifiers=disabled
• D、netsh.exe interface ipv6 set privacy state=enabled

第21题：

第22题：

第23题：

第24题：