Which of the following is true concerning Frame Relay multipoint subinterfaces?()A. An IP address is required on the physical interface of the central router.B. All routers are required to be fully meshed.C. All routers must be in the same subnet to forwa

题目
Which of the following is true concerning Frame Relay multipoint subinterfaces?()

A. An IP address is required on the physical interface of the central router.

B. All routers are required to be fully meshed.

C. All routers must be in the same subnet to forward routing updates and broadcasts.

D. Multipoint is the default configuration for Frame Relay subinterfaces.

相似考题

1.Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-type

2.It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit.Which of the following processes are required to accomplish this task?()A. configure static frame relay map entries for each subinterface network.B. remove the ip address from the physical interfaceC. create the virtual interfaces with the interface commandD. configure each subinterface with its own IP addressE. disable split horizon to prevent routing loops between the subinterface networksF. encapsulate the physical interface with multipoint PPP

3.Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?（）A、TestKRouter(config-if)# Encapsulation frame-relay dot1qB、TestKRouter(config-if)# Encapsulation frame-relay aal5snapC、TestKRouter(config-if)# Encapsulation frame-relay ietfD、TestKRouter(config-if)# Encapsulation frame-relay islE、None of the above

4.When configuring Frame Relay using point－to－point subinterfaces, which of the following must not be configured?()A. The local DLCI on each subinterface of the Frame Relay.B. The Frame Relay encapsulation on the physical interface.C. An IP address on the physical interface.D. The subinterface type as point-to-point

参考答案和解析
参考答案：C
更多“Which of the following is true concerning Frame Relay multipoint subinterfaces?() ”相关问题

  • 第1题：

    A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）

    • A、The central site router has 100 fully adjacent neighborships with the 100 branches
    • B、The central  site router has neighborships with all branch routers, but fully adjacent neighbors with only two branches
    • C、The central site router has a neighborship with the Frame Relay switcH
    • D、None of the other answers is correct

    正确答案:A

  • 第2题：

    Which of the following is true concerning Frame Relay multipoint subinterfaces?（）

    • A、An IP address is required on the physical interface of the central router.
    • B、All routers are required to be fully meshed.
    • C、All routers must be in the same subnet to forward routing updates and broadcasts.
    • D、Multipoint is the default configuration for Frame Relay subinterfaces.

    正确答案:C

  • 第3题：

    The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command？（）

    • A、This command should be executed from the global configuration mode.
    • B、The IP address 10.121.16.8 is the local router port used to forward data.
    • C、102 is the remote DLCI that will receive the information.
    • D、This command is required for all Frame Relay configurations.
    • E、The broadcast option allows packets， such as RIP updates， to be forwarded across the PVC

    正确答案:E

  • 第4题：

    Which command can be used to verify the DLCI destination address in a Frame Relay static configuration?（）

    • A、show frame-relay end-to-end
    • B、show frame-relay map
    • C、show frame-relay lmi
    • D、show frame-relay pvc

    正确答案:B

  • 第5题：

    It has become necessary to configure an existing serial interface to accept a second Frame Relay virtualcircuit.Which of the following processes are required to accomplish this task？（）

    • A、configure static frame relay map entries for each subinterface network.
    • B、remove the ip address from the physical interface
    • C、create the virtual interfaces with the interface command
    • D、configure each subinterface with its own IP address
    • E、disable split horizon to prevent routing loops between the subinterface networks
    • F、encapsulate the physical interface with multipoint PPP

    正确答案:B,C,D

  • 第6题：

    You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）

    • A、The Frame Relay encapsulation on the physical interface.
    • B、The local DLCI on each subinterface.
    • C、An IP address on the physical interface.
    • D、The subinterface type as point-to-point.

    正确答案:C

  • 第7题：

    单选题
    The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command？（）
    A

    This command should be executed from the global configuration mode.

    B

    The IP address 10.121.16.8 is the local router port used to forward data.

    C

    102 is the remote DLCI that will receive the information.

    D

    This command is required for all Frame Relay configurations.

    E

    The broadcast option allows packets， such as RIP updates， to be forwarded across the PVC


    正确答案： A
    解析： 暂无解析

  • 第8题：

    单选题
    The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command（）。
    A

    This command should be executed from the global configuration mode

    B

    The IP address 10.121.16.8 is the local router port used to forward data

    C

    102 is the remote DLCI that will receive the information

    D

    This command is required for all Frame Relay configurations

    E

    The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC


    正确答案： C
    解析： 暂无解析

  • 第9题：

    单选题
    Which of the following is true concerning Frame Relay multipoint subinterfaces?（）
    A

    An IP address is required on the physical interface of the central router.

    B

    All routers are required to be fully meshed.

    C

    All routers must be in the same subnet to forward routing updates and broadcasts.

    D

    Multipoint is the default configuration for Frame Relay subinterfaces.


    正确答案： C
    解析： 暂无解析

  • 第10题：

    单选题
    A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）
    A

    The central site router has 100 fully adjacent neighborships with the 100 branches

    B

    The central  site router has neighborships with all branch routers, but fully adjacent neighbors with only two branches

    C

    The central site router has a neighborship with the Frame Relay switcH

    D

    None of the other answers is correct


    正确答案： A
    解析： 暂无解析

  • 第11题：

    单选题
    A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?（）
    A

    Router(config-if)# encapsulation frame-relay q933a

    B

    Router(config-if)# encapsulation frame-relay ansi

    C

    Router(config-if)# encapsulation frame-relay ietf

    D

    Router(config-if)# encapsulation frame-relay isl

    E

    None of the above


    正确答案： E
    解析： 暂无解析

  • 第12题：

    单选题
    Which statement is true about the configuration of AutoQoS on a Frame Relay interface？（）
    A

    AutoQoS can be configured from a different subinterface if the DLCI is already assigned to one subinterface 

    B

    Multilink PPP (MLP) over Frame Relay must be manually configured on low speed DLCIs 

    C

    for low-speed Frame Relay DLCIs with Frame Relay-to ATM interworking, the AutoQoS cannot be configured if a virtual template is already configured for the DLCI 

    D

    AutoQoS can be configured on a Frame Relay DLCI only if a map class is attached to the DLCI 


    正确答案： C
    解析： 暂无解析

  • 第13题：

    A new frame relay connection is being brought up. Which of the following are frame relay LMI type options that can be configured on this new link?（）

    • A、EIA/TIA
    • B、Q.932
    • C、Q.933A
    • D、IEEE
    • E、Cisco
    • F、Annex D

    正确答案:C,E,F

  • 第14题：

    When configuring Frame Relay using point-to-point subinterfaces, which of the following must not be configured?（）

    • A、The local DLCI on each subinterface of the Frame Relay.
    • B、The Frame Relay encapsulation on the physical interface.
    • C、An IP address on the physical interface.
    • D、The subinterface type as point-to-point

    正确答案:C

  • 第15题：

    Which three statements about L2TPv3 are true？（）

    • A、L2TPv3 Frame Relay support includes only 32-bit DLCI addressing
    • B、L2TPv3 sessions do not support Frame Relay LMI interworking
    • C、Multipoint DLCI is not supported
    • D、To use DCE or a Network-to-Network Interface on a Frame Relay port， you must configure the frame-relay switching command
    • E、L2TPv3 feature does not support Frame Relay extended addressing

    正确答案:B,D,E

  • 第16题：

    What is the advantage of using a multipoint interface instead of point-to-point subinterfaces when configuring a Frame Relay hub in a hub-and-spoke topology?（）

    • A、it avoids split-horizon issues with distance vector routing protocols.
    • B、IP addresses can be conserved if VLSM is not being used for subnetting.
    • C、A multipoint interface offers greater security compared to point-to-point subinterface configurations.
    • D、The multiple IP network addresses required for a multipoint interface provide greater addressing flexibility over point-to-point configurations.

    正确答案:B

  • 第17题：

    Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）

    • A、frame-relay arp
    • B、frame-relay map
    • C、frame-relay interface-dlci
    • D、frame-relay lmi-type

    正确答案:B

  • 第18题：

    The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command（）。

    • A、This command should be executed from the global configuration mode
    • B、The IP address 10.121.16.8 is the local router port used to forward data
    • C、102 is the remote DLCI that will receive the information
    • D、This command is required for all Frame Relay configurations
    • E、The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC

    正确答案:E

  • 第19题：

    单选题
    You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）
    A

    The Frame Relay encapsulation on the physical interface.

    B

    The local DLCI on each subinterface.

    C

    An IP address on the physical interface.

    D

    The subinterface type as point-to-point.


    正确答案： B
    解析： 暂无解析

  • 第20题：

    单选题
    In Frame Relay， FECN messages indicating congestion are sent or received by which of following？（）
    A

    Sent by the destination

    B

    Received by the sender

    C

    Received by the destination

    D

    Sent by the sender


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    When configuring Frame Relay using point-to-point subinterfaces, which of the following must not be configured?（）
    A

    The local DLCI on each subinterface of the Frame Relay.

    B

    The Frame Relay encapsulation on the physical interface.

    C

    An IP address on the physical interface.

    D

    The subinterface type as point-to-point


    正确答案： B
    解析： 暂无解析

  • 第22题：

    多选题
    Which two Cisco AutoQoS interface statements are true？（）
    A

    AutoQoS is supported on Frame Relay multipoint subinterfaces.

    B

    AutoQoS is supported on low-speed ATM PVCs in point-to-point subinterfaces.

    C

    AutoQoS is supported on serial PPP and HDLC interfaces.

    D

    AutoQoS is supported only on Frame Relay main interfaces and not on any subinterface configuration.


    正确答案： D,B
    解析： 暂无解析

  • 第23题：

    多选题
    Which three statements about L2TPv3 are true？（）
    A

    L2TPv3 Frame Relay support includes only 32-bit DLCI addressing

    B

    L2TPv3 sessions do not support Frame Relay LMI interworking

    C

    Multipoint DLCI is not supported

    D

    To use DCE or a Network-to-Network Interface on a Frame Relay port， you must configure the frame-relay switching command

    E

    L2TPv3 feature does not support Frame Relay extended addressing


    正确答案： B,D,E
    解析： 暂无解析

  • 第24题：

    多选题
    A new frame relay connection is being brought up. Which of the following are frame relay LMI type options that can be configured on this new link?（）
    A

    EIA/TIA

    B

    Q.932

    C

    Q.933A

    D

    IEEE

    E

    Cisco

    F

    Annex D


    正确答案： F,B
    解析： 暂无解析

相关内容