Which command can be used to determine the type of cable attached to the Serial 0／0 interface on a router?()A. show interfaces serial 0/0B. show running-configC. show versionD. show controllers serial 0/0E. show ip interfaceF. show line serial 0/0

题目
Which command can be used to determine the type of cable attached to the Serial 0／0 interface on a router?()

A. show interfaces serial 0/0

B. show running-config

C. show version

D. show controllers serial 0/0

E. show ip interface

F. show line serial 0/0

相似考题

1.An administrator issues the show ip interface s0/0 command and the output displays that interface Serial0/0 is up, line protocol is up.What does "line protocol is up" specifically indicate about the interface?A．The cable is attached properly.B．CDP has discovered the connected device.C．Keepalives are being received on the interface.D．A carrier detect signal has been received from the connected device.E．IP is correctly configured on the interface.

2.Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）A. Declare router B a stub router using the eigrp stub command.B. Use the passive - interface command for interface Serial0/0/0.C. Use a mask with the network command to exclude interface Serial0/0/0.D. Implement a distribute list to exclude the link prefix from the routi ng updates.

3.What is the purpose of the OSPF router ID in a OR／BOR election?()A. It is used with the OSPF priority values to determine which OSPF router will become the DR or BOR in a point-to-point networkB. It is used with the OSPF priority values to determine which interface will be used to form a neighbor relationship with another OSPF routerC. It is used with the OSPF priority values to determine which router will become the DR or BOR in a multi access networkD. It is used to determine which interfaces will send Hello packets to neighboring OSPF routers

4.Which type of cable should be used to make a connection between the Fa0/0 port on a router and the Fa0/0 port switch?A．Rollover cableB．Console cableC．Crossover cableD．Straight-through cableE．Serial cable

参考答案和解析
参考答案：D
更多“Which command can be used to determine the type of cable attached to the Serial 0／0 interface on a router?() ”相关问题

  • 第1题：

    Refer to the exhibit. Looking at the topology diagram and the partial router configurations shown, which statement is true? ()

    A.The NProuter has two OSPF neighbors in the "Full" adjacency state

    B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds

    C.The NProuter serial0/0 interface has been configured with an OSPF network type of "pointtopoint"

    D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting

    E.The "Mismatched" error is caus ed by the expiration of the OSPF timers


    参考答案：E

  • 第2题：

    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

    A. Serial 0 is up, line protocol is up

    B. Serial 0 is up, line protocol is down

    C. Serial 0 is down, line protocol is down

    D. Serial 0 is down, line protocol is up

    E. Serial 0 is administratively down, line protocol is down

    F. Serial 0 is administratively down, line protocol is up


    参考答案：E

  • 第3题：

    Part of the configuration files for routers testking1 and testking2 are displayed below:If you were to enter the "show interface serial 0" command on router testking1,which of the following will be displayed?（）

    A. Serial 0 is down, line protocol is down

    B. Serial 0 is up, line protocol is up

    C. Open: IPCP, CDPCP

    D. LCP closed

    E. LCP open


    参考答案：B, E

  • 第4题：

    Usetheoutputfromtheroutershowninthegraphicabovetodeterminewhichofthefollowingarecorrect.()

    A.Router John uses alink-state routing protocol.

    B.Router John will receive routing updates on the Serial0/0 interface.

    C.Router John will receive routing updates on the Serial0/1 interface.

    D.Router John will send routing updates out the Serial0/0 interface.

    E.Router John will send routing updates out the FastEthernet0/0 interface.

    F.Router John will send routing updates out the Serial0/1 interface.


    参考答案：B, D

  • 第5题：

    Use the output from the router shown in the graphic above to determine which of the following are correct.()

    A. Router John uses a link-state routing protocol.

    B. Router John will receive routing updates on the Serial0/0 interface.

    C. Router John will receive routing updates on the Serial0/1 interface.

    D. Router John will send routing updates out the Serial0/0 interface.

    E. Router John will send routing updates out the FastEthernet0/0 interface.

    F. Router John will send routing updates out the Serial0/1 interface.


    参考答案：B, D

  • 第6题：

    What is the purpose of this command? ip route 0.0.0.0 0.0.0.0 serial0/0（）

    • A、It configures a router to send all packets out interface serial 0/0.
    • B、It configures a router to block routing updates from being sent out interface serial 0/0.
    • C、It configures a router as a firewall, blocking all unauthorized packets from exiting serial 0/0.
    • D、It configures a router to send all packets for unknown destination networks out interface serial 0/0.
    • E、It configures a router to drop all packets for which the destination network is unknown.

    正确答案:D

  • 第7题：

    What is the purpose of the OSPF router ID in a OR/BOR election?（）

    • A、It is used with the OSPF priority values to determine which OSPF router will become the DR or BOR in a point-to-point network
    • B、It is used with the OSPF priority values to determine which interface will be used to form a neighbor relationship with another OSPF router
    • C、It is used with the OSPF priority values to determine which router will become the DR or BOR in a multi access network
    • D、It is used to determine which interfaces will send Hello packets to neighboring OSPF routers

    正确答案:C

  • 第8题：

    Which two privileged mode cisco ios commands can be used to determine a cisco router chassis serial number?（）

    • A、show inventory
    • B、show flash：filesys
    • C、dirflash：include chassis
    • D、show diag
    • E、show controllers

    正确答案:A,D

  • 第9题：

    Which type of cable should be used to make a connection between the Fa0/0 port on a router and the Fa0/0 port switch?（）

    • A、Rollover cable
    • B、Console cab le
    • C、Crossover cable
    • D、Straight-through cable
    • E、Serial cable

    正确答案:C

  • 第10题：

    单选题
    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）
    A

    Serial 0 is up, line protocol is up

    B

    Serial 0 is up, line protocol is down

    C

    Serial 0 is down, line protocol is down

    D

    Serial 0 is down, line protocol is up

    E

    Serial 0 is administratively down, line protocol is down

    F

    Serial 0 is administratively down, line protocol is up


    正确答案： D
    解析： 暂无解析

  • 第11题：

    单选题
    Which type of cable should be used to make a connection between the Fa0/0 port on a router and the Fa0/0 port switch?（）
    A

    Rollover cable

    B

    Console cab le

    C

    Crossover cable

    D

    Straight-through cable

    E

    Serial cable


    正确答案： D
    解析： 暂无解析

  • 第12题：

    单选题
    Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?（）
    A

    show interfaces serial 0/0

    B

    show running-config

    C

    show version

    D

    show controllers serial 0/0

    E

    show ip interface

    F

    show line serial 0/0


    正确答案： E
    解析： 暂无解析

  • 第13题：

    TestKing.com is configuring the serial interface of a Cisco router to connect to the router of a new ISP. A full T1 is being used for the Internet connection. After issuing the show interface serial 0/0 command, it is observed that the interface is UP and the line protocol is DOWN.Which of the following commands could fix this problem?（）

    A. Border# copy running-config startup-config

    B. Border(config)# no shutdown

    C. Border(config-if)# encapsulation ppp

    D. Border(config-if)# no cdp enable

    E. Border(config-if)# ip routing


    参考答案：C

  • 第14题：

    There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:From your observations of the above exhibit, what is the underlying cause of the problem?（）

    A. The loopback is not set.

    B. The serial cable is faulty.

    C. The subnet mask is not configured properly.

    D. The IP address is not configured properly.

    E. The Layer 2 frame types are not compatible.

    F. The keepalive setting is not configured properly.


    参考答案：E

  • 第15题：

    Refer to the exhibit.The network administrator is in acampus building distant from Building B.WANRouter is hosting a newly installed WAN link on interface S0/0.The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface.How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner?（）

    A.Telnet to WANRouter and execute the command show interfaces S0/0

    B.Telnet to WANRouter and execute the commandshow processes S0/0

    C.Telnet to WANRouter and execute the command show running-configuration

    D.Telnet to WANRouter and execute the command show controller S0/0

    E.Physically examine the cable between WANRouter S0/0 and the DCE.

    F.Establish a console sessionon WANRouter and execute the command show interfaces S0/0


    参考答案：D

  • 第16题：

    The network administrator is in a campus building distant from Building B. WANRouter is hosting a newly installed WAN link on interface S0/0. The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface. How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner（）。

    A.Telnet to WANRouter and execute the command show interfaces S0/0

    B.Telnet to WANRouter and execute the command show processes S0/0

    C.Telnet to WANRouter and execute the command show running-configuration

    D.Telnet to WANRouter and execute the command show controller S0/0

    E.Physically examine the cable between WANRouter S0/0 and the DCE

    F.Establish a console session on WANRouter and execute the command show interfaces S0/0


    参考答案：D

  • 第17题：

    Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?（）

    • A、show interfaces serial 0/0
    • B、show running-config
    • C、show version
    • D、show controllers serial 0/0
    • E、show ip interface
    • F、show line serial 0/0

    正确答案:D

  • 第18题：

    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

    • A、Serial 0 is up, line protocol is up
    • B、Serial 0 is up, line protocol is down
    • C、Serial 0 is down, line protocol is down
    • D、Serial 0 is down, line protocol is up
    • E、Serial 0 is administratively down, line protocol is down
    • F、Serial 0 is administratively down, line protocol is up

    正确答案:E

  • 第19题：

    Which command can be used to filter a RIPv6 route from getting installed in the routing table？（）

    • A、ipv6 router rip ccie distribute-list..
    • B、ipv6 router rip ccie offset-list..
    • C、interface e0/0 ipv6 rip ccie distribute-list..
    • D、interface e0/0 ipv6 rip ccie advertise..

    正确答案:A

  • 第20题：

    TestKing.com is configuring the serial interface of a Cisco router to connect to the router of a new ISP. A full T1 is being used for the Internet connection. After issuing the show interface serial 0/0 command, it is observed that the interface is UP and the line protocol is DOWN. Which of the following commands could fix this problem?（）

    • A、Border# copy running-config startup-config
    • B、Border(config)# no shutdown
    • C、Border(config-if)# encapsulation ppp
    • D、Border(config-if)# no cdp enable
    • E、Border(config-if)# ip routing

    正确答案:C

  • 第21题：

    The network administrator is in a campus building distant from Building B. WANRouter is hosting a newly installed WAN link on interface S0/0. The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface. How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner（）。

    • A、Telnet to WANRouter and execute the command show interfaces S0/0
    • B、Telnet to WANRouter and execute the command show processes S0/0
    • C、Telnet to WANRouter and execute the command show running-configuration
    • D、Telnet to WANRouter and execute the command show controller S0/0
    • E、Physically examine the cable between WANRouter S0/0 and the DCE
    • F、Establish a console session on WANRouter and execute the command show interfaces S0/0

    正确答案:D

  • 第22题：

    多选题
    Which two privileged mode cisco ios commands can be used to determine a cisco router chassis serial number?（）
    A

    show inventory

    B

    show flash：filesys

    C

    dirflash：include chassis

    D

    show diag

    E

    show controllers


    正确答案： A,C
    解析： 暂无解析

  • 第23题：

    单选题
    What is the purpose of this command? ip route 0.0.0.0 0.0.0.0 serial0/0（）
    A

    It configures a router to send all packets out interface serial 0/0.

    B

    It configures a router to block routing updates from being sent out interface serial 0/0.

    C

    It configures a router as a firewall, blocking all unauthorized packets from exiting serial 0/0.

    D

    It configures a router to send all packets for unknown destination networks out interface serial 0/0.

    E

    It configures a router to drop all packets for which the destination network is unknown.


    正确答案： A
    解析： 暂无解析

相关内容