There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:From your observations of the above exhibit, what is the underlying cause of the problem?()
A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.
第1题:
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?()
A. Declare router B a stub router using the eigrp stub command.
B. Use the passive - interface command for interface Serial0/0/0.
C. Use a mask with the network command to exclude interface Serial0/0/0.
D. Implement a distribute list to exclude the link prefix from the routi ng updates.
第2题:
TestKing.com is configuring the serial interface of a Cisco router to connect to the router of a new ISP. A full T1 is being used for the Internet connection. After issuing the show interface serial 0/0 command, it is observed that the interface is UP and the line protocol is DOWN.Which of the following commands could fix this problem?()
A. Border# copy running-config startup-config
B. Border(config)# no shutdown
C. Border(config-if)# encapsulation ppp
D. Border(config-if)# no cdp enable
E. Border(config-if)# ip routing
第3题:
The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?()
A. The authentication needs to be changed to PAP for both routers.
B. The serial IP addresses of routers are not on the same subnet.
C. The username/password combination is incorrectly configured.
D. The router names are incorrectly configured.
第4题:
Refer to the exhibit. The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? ()
A.The Manchester serial address is 10.1.1.1
B.The Manchester serial address is 10.1.1.2
C.这个Manchester路由器串口地址为:10.1.12
D.The London router is a Cisco 2610.
E.The Manchester router is a Cisco 2610.
F.The CDP information was received on port Serial0/0 of the Manchester router.
G.The CDP information was sent by port Serial0/0 of the London Router.
第5题:
A. Router John uses a link-state routing protocol.
B. Router John will receive routing updates on the Serial0/0 interface.
C. Router John will receive routing updates on the Serial0/1 interface.
D. Router John will send routing updates out the Serial0/0 interface.
E. Router John will send routing updates out the FastEthernet0/0 interface.
F. Router John will send routing updates out the Serial0/1 interface.
第6题:
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below: Gateway of last resort is 10.1.2.2 to network 0.0.0.0 10.0.0.0/24 is subnetted, 2 subnets R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0 C 10.1.2.0 is directly connected, Serial0/0 C 10.1.5.0 is directly connected, Serial0/1 C 10.1.6.0 is directly connected, FastEthernet0/0 R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1 Based on the output above, if an administrator pings host 10.1.8.5 from host 10.1.6.100, how will the router TestkingA process the ICMP packets?()
第7题:
While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?()
第8题:
TestKing.com is configuring the serial interface of a Cisco router to connect to the router of a new ISP. A full T1 is being used for the Internet connection. After issuing the show interface serial 0/0 command, it is observed that the interface is UP and the line protocol is DOWN. Which of the following commands could fix this problem?()
第9题:
Which line from the output of the show ip interface command indicates a layer 1 problem?()
第10题:
The Popcorn router is not forwarding RIP updates.
The Popcorn router did not include network 192.168.12.0 in its routing configuration.
The Ethernet1 interface of the Popcorn router is shutdown.
The clockrate is not present in the configuration of one of the routers.
The Serial interface of the Popcorn router is not operating.
第11题:
It configures a router to send all packets out interface serial 0/0.
It configures a router to block routing updates from being sent out interface serial 0/0.
It configures a router as a firewall, blocking all unauthorized packets from exiting serial 0/0.
It configures a router to send all packets for unknown destination networks out interface serial 0/0.
It configures a router to drop all packets for which the destination network is unknown.
第12题:
show interfaces serial 0/0
show running-config
show version
show controllers serial 0/0
show ip interface
show line serial 0/0
第13题:
A. show interfaces serial 0/0
B. show running-config
C. show version
D. show controllers serial 0/0
E. show ip interface
F. show line serial 0/0
第14题:
While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?()
A. Serial 0 is up, line protocol is up
B. Serial 0 is up, line protocol is down
C. Serial 0 is down, line protocol is down
D. Serial 0 is down, line protocol is up
E. Serial 0 is administratively down, line protocol is down
F. Serial 0 is administratively down, line protocol is up
第15题:
Part of the configuration files for routers testking1 and testking2 are displayed below:If you were to enter the "show interface serial 0" command on router testking1,which of the following will be displayed?()
A. Serial 0 is down, line protocol is down
B. Serial 0 is up, line protocol is up
C. Open: IPCP, CDPCP
D. LCP closed
E. LCP open
第16题:
A.Router John uses alink-state routing protocol.
B.Router John will receive routing updates on the Serial0/0 interface.
C.Router John will receive routing updates on the Serial0/1 interface.
D.Router John will send routing updates out the Serial0/0 interface.
E.Router John will send routing updates out the FastEthernet0/0 interface.
F.Router John will send routing updates out the Serial0/1 interface.
第17题:
Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?()
第18题:
What is the purpose of this command? ip route 0.0.0.0 0.0.0.0 serial0/0()
第19题:
A standard access control list has been configured on a router and applied to interface Serial 0 in anoutbound direction. No ACL is applied to Interface Serial 1 on the same router. What will happen whentraffic being filtered by the access list does not match the configured ACL statements for Serial 0?()
第20题:
The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?()
第21题:
Serial 0 is up, line protocol is up
Serial 0 is up, line protocol is down
Serial 0 is down, line protocol is down
Serial 0 is down, line protocol is up
Serial 0 is administratively down, line protocol is down
Serial 0 is administratively down, line protocol is up
第22题:
Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#no shut
Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)#no shut
Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation frame-relay Main(config-if)#authenication chap Main(config-if)#no shut
Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ppp Main(config-if)#no shut
第23题:
The traffic is dropped
The resulting action is determined by the destination IP address
The source IP address is checked,and,if a match is not found, traffic is routed out interface Serial 1
The resulting action is determined by the destination IP address and port number