After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?()A. >B. #C. ?D. *E. All of the aboveF. None of the above

题目
After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?()

A. >

B. #

C. ?

D. *

E. All of the above

F. None of the above

相似考题

1.下面不是路由器配置超级用户口令的命令是( )。A) Router(config)#enable password 7 phyr123B) Router(config)#enable secret phy123C) Router(config)#enable password phyr123D) Router(config-line)#password 7 222307

2.You want to log into the router and make a configuration change.After loggin in as the root user, what is the next command you must enter?()A. enableB. configureC. editD. cli

3.After logging into a router and typing in a few show commands, you press the up arrow key. What will this do?A．It will recall the previous command lineB．It will move the cursor one line upC．It will redisplay the current command lineD．It will capitalize the command lineE．None of the above

4.You are a senior network administrator at Ezonexam, and while performing the password recovery procedure on your 2500 series Cisco router, you type in the following command:o/r 0x2142What is the purpose of this command?A．It is used to restart the router.B．It is used to bypass the configuration in NVRAM.C．It is used to enter ROM Monitor mode.D．It is used to view the lost password.E．It is used to save the changes to the configuration.

更多“After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?() ”相关问题

  • 第1题：

    How can a Ezonexam administrator determine if a router has been configured when it is first powered up?

    A．A configured router prompts for a password

    B．A configured router goes to the privileged mode prompt

    C．An un configured router goes into the setup dialog

    D．An un configured router goes to the enable mode prompt


    正确答案：C
    解析：Explanation:
    If a non-configured router is started, then it goes into setup mode and ask for the minimum configuration parameters (hostname, IP address to interfaces, enable password, etc). If the router is already configured it boots by implementing the saved startup-config.

  • 第2题：

    After attempting to telnet into a router, you are denied and you receive the error message "password required, but none set." What configuration changes will allow telnet access into this router?()

    A.

    B.

    C.

    D.


    参考答案：C

  • 第3题：

    下列选项中，哪一项不是路由器配置超级用户的口令( )。

    A．Router (config) # enable secret phy l23

    B．Router (config) # password 7phy 123

    C．Router (config) # enable password phy 123

    D．Router (config) # enable password 7Phy l23


    正确答案：B

  • 第4题：

    The enable secret password appears as an MD5 hash in a router’s configuration file， whereas the enablepassword is not hashed （or encrypted， if the password-encryption service is not enabled）. What is thereason that Cisco still support the use of both enable secret and enable passwords in a router’sconfiguration？（）

    • A、The enable password is present for backward compatibility.
    • B、Because the enable secret password is a hash， it cannot be decrypted. Therefore， the enable password is used to match the password that was entered， and the enable secret is used to verify that the enablepassword has not been modified since the hash was generated.
    • C、The enable password is considered to be a router’s public key， whereas the enable secret password is considered to be a router’s private key.
    • D、The enable password is used for IKE Phase I， whereas the enable secret password is used for IKE Phase II.

    正确答案:A

  • 第5题：

    When should you enable Network Address Translation Transparency (NAT-T) on the Teleworker?（）

    • A、when a router between the Teleworker router and the head-end VPN router is doing NAT/pNAT and does not support IPSec pass-through 
    • B、when the Teleworker router itself is doing NAT/pNAT
    • C、always
    • D、never

    正确答案:A

  • 第6题：

    After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?（）

    • A、>
    • B、#
    • C、?
    • D、*
    • E、All of the above
    • F、None of the above

    正确答案:B

  • 第7题：

    A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）

    • A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.
    • B、  When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.
    • C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.
    • D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.
    • E、None of the other answers is correct.

    正确答案:E

  • 第8题：

    单选题
    You are a senior network administrator at TestKing, and while performing thepassword recovery procedure on your 2500 series Cisco router, you type in thefollowing command:o/r 0x2142What is the purpose of this command?（）
    A

    It is used to restart the router.

    B

    It is used to bypass the configuration in NVRAM.

    C

    It is used to enter ROM Monitor mode.

    D

    It is used to view the lost password.

    E

    It is used to save the changes to the configuration.


    正确答案： B
    解析： 暂无解析

  • 第9题：

    单选题
    A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）
    A

    When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.

    B

      When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.

    C

    When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.

    D

    When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.

    E

    None of the other answers is correct.


    正确答案： C
    解析： 暂无解析

  • 第10题：

    单选题
    You want to log in to the router and make a configuration change. After logging in as the root user, what is the next command you must enter?（）
    A

    enable

    B

    configure

    C

    edit

    D

    cli


    正确答案： C
    解析： 暂无解析

  • 第11题：

    单选题
    The enable secret password appears as an MD5 hash in a router’s configuration file， whereas the enablepassword is not hashed （or encrypted， if the password-encryption service is not enabled）. What is thereason that Cisco still support the use of both enable secret and enable passwords in a router’sconfiguration？（）
    A

    The enable password is present for backward compatibility.

    B

    Because the enable secret password is a hash， it cannot be decrypted. Therefore， the enable password is used to match the password that was entered， and the enable secret is used to verify that the enablepassword has not been modified since the hash was generated.

    C

    The enable password is considered to be a router’s public key， whereas the enable secret password is considered to be a router’s private key.

    D

    The enable password is used for IKE Phase I， whereas the enable secret password is used for IKE Phase II.


    正确答案： A
    解析： 暂无解析

  • 第12题：

    单选题
    What must you type to enter operational mode from the root@% command prompt?（）
    A

    exit

    B

    configure

    C

    edit

    D

    cli


    正确答案： A
    解析： 暂无解析

  • 第13题：

    以下哪个不是路由器配置超级用户口令?

    A.Router(config．#enable password 7 phy123

    B.Router(config．#enable secret phy123

    C.Router(config．#enable password phy123

    D.Router(config-line．#password 7 zzz307


    正确答案：D

  • 第14题：

    以下哪个不是路由器配置超级用户的口令______。

    A．Router (config) #enable password 7 phy 123

    B．Router (config) #enable secret phy 123

    C．Router (config) #enable password phy 123

    D．Router (config) #password 7 phy 123


    正确答案：D

  • 第15题：

    After logging into a router and typing in a few show commands, you press the up arrow key. What will this do?（）

    • A、It will recall the previous command line
    • B、It will move the cursor one line up
    • C、It will redisplay the current command line
    • D、It will capitalize the command line
    • E、None of the above

    正确答案:A

  • 第16题：

    You are a senior network administrator at TestKing, and while performing thepassword recovery procedure on your 2500 series Cisco router, you type in thefollowing command:o/r 0x2142What is the purpose of this command?（）

    • A、It is used to restart the router.
    • B、It is used to bypass the configuration in NVRAM.
    • C、It is used to enter ROM Monitor mode.
    • D、It is used to view the lost password.
    • E、It is used to save the changes to the configuration.

    正确答案:B

  • 第17题：

    What is the effect of using the service password-encryption command?（）

    • A、only passwords configured after the command has been entered will be encrypted
    • B、Only the enable password will be encrypted
    • C、Only the enable secret password will be encrypted
    • D、It will encrypt the secret password and remove the enable secret password from the configuration
    • E、It will encrypt all current and future passwords.

    正确答案:E

  • 第18题：

    How can an administrator determine if a router has been configured when it is first powered up?（）

    • A、A configured router prompts for a password
    • B、A configured router goes to the privileged mode prompt
    • C、An un configured router goes into the setup dialog
    • D、An un configured router goes to the enable mode prompt

    正确答案:C

  • 第19题：

    You need to configure the local security policy setting to request a user name and password when you make changes to the computer system.  What should you do？（）

    • A、Enable the Password must meet complexity requirements setting.
    • B、Enable the User Account Control： Detect application installations and prompt for elevation setting.
    • C、Configure the Interactive logon： Prompt user to change password before expiration setting to a value between 1 and 999.
    • D、Configure the User Account Control： Behavior of the elevation prompt for administrators in Admin Approval mode setting to the Prompt for credentials option.

    正确答案:D

  • 第20题：

    单选题
    After logging into a router, you type in "enable" and then enter the correct password when prompted. What is the current router prompt symbol at this point?（）
    A

    >

    B

    #

    C

    ?

    D

    *

    E

    All of the above

    F

    None of the above


    正确答案： B
    解析： 暂无解析

  • 第21题：

    单选题
    After logging into a router and typing in a few show commands, you press the up arrow key. What will this do?（）
    A

    It will recall the previous command line

    B

    It will move the cursor one line up

    C

    It will redisplay the current command line

    D

    It will capitalize the command line

    E

    None of the above


    正确答案： B
    解析： 暂无解析

  • 第22题：

    单选题
    You want to log into the router and make a configuration change.After loggin in as the root user, what is the next command you must enter?（）
    A

    enable

    B

    configure

    C

    edit

    D

    cli


    正确答案： D
    解析： 暂无解析

  • 第23题：

    单选题
    How can an administrator determine if a router has been configured when it is first powered up?（）
    A

    A configured router prompts for a password

    B

    A configured router goes to the privileged mode prompt

    C

    An un configured router goes into the setup dialog

    D

    An un configured router goes to the enable mode prompt


    正确答案： C
    解析： 暂无解析

相关内容