A customer has a Fibre Channel switch residing in a configuration where both production and test data coexist. Which of the following is the simplest method for ensuring that the two types of data do not flow through the same port?（）A.VLANB.zoningC.trunki

题目

A customer has a Fibre Channel switch residing in a configuration where both production and test data coexist. Which of the following is the simplest method for ensuring that the two types of data do not flow through the same port?（）

A.VLAN

B.zoning

C.trunking

D.LUN masking

相似考题

1.A customer has two single cluster IBM TS7700 Virtualization Engines at the same site. The customer wants to move one to a remote site and set up a grid configuration with the two clusters. The customer has fibre between the two sites. What is the most important factor to consider when planning the new configuration?（）A. operator trainingB. cache size of the two clustersC. fibre bandwidth capability between the sitesD. number of stacked tape drives attached to each cluster

2.A Fibre Channel fabric （or Fibre Channel switched fabric， FC-SW） is a switched fabric of FibreChannel devices enabled by a Fibre Channel switch. Fabrics are normally subdivided by Fibre Channel zoning. Each fabric has a name server and provides other services. Higher redundancy over FC-AL，P2P.Which path selection protocol is used by Fibre Channel fabrics？（）A、 OSPFB、 RIPC、 FSPFD、 VSANs

3.A Fibre Channel fabric (or Fibre Channel switched fabric, FC-SW) is a switched fabric of Fibre Channel devices enabled by a Fibre Channel switch. Fabrics are normally subdivided by Fibre Channel zoning.Each fabric has a name server and provides other services. Higher redundancy over FC-AL, P2P.Which path selection protocol is used by Fibre Channel fabrics?（）A、OSPFB、RIPC、FSPFD、VSANs

4.In a Cisco Unified Computing System， where are SAN port channels connected to？（）A、 Only to Cisco Fibre Channel switchesB、 Only to Cisco Fibre Channel switches in NPIV modeC、 To any Fibre Channel switchD、 Directly to storage arraysE、 Only to Nexus Switches

更多“A customer has a Fibre Channel switch residing in a configuration where both production an ”相关问题

  • 第1题：

    Which of the following describes the advantage of using Fibre Channel over Ethernet （FCoE） in POWER6 and POWER7 Blades？（）

    • A、The FCoE card provides both LAN and fibre channel function from a single card on the blade. 
    • B、The FCoE advanced technology removes the need for any BladeCenter switching to support this function.
    • C、Component reliability on the fibre channel over Ethernet is higher than on regular Ethernet and fibre channel adapters.
    • D、The AIX device driver for FCoE has been completely rewritten for the current adapter， eliminating errors and performance issues.

    正确答案:A

  • 第2题：

    A customer wants to boot from SAN with their IBM BladeCenter infrastructure.  What is required for the customer to be able to perform this？ （）

    • A、4GB Modular Flash Drive for each Blade Server and Dual 15.8GB 2.5 Solid State Drive for each Blade Server 
    • B、Cisco Intelligent Gb Ethernet Switch Module and IBM BladeCenter Copper Pass-thru Module 
    • C、Fibre Channel Expansion Card for each Blade Server and Fibre Channel SAN Switch Module 
    • D、Cisco Intelligent Gb Ethernet Switch Module and Dual 15.8GB 2.5 Solid State Drive for each Blade Server

    正确答案:C

  • 第3题：

    A customer has two single cluster IBM TS7700 Virtualization Engines at the same site. The customer wants to move one to a remote site and set up a grid configuration with the two clusters. The customer has fibre between the two sites. What is the most important factor to consider when planning the new configuration?（）

    • A、operator training
    • B、cache size of the two clusters
    • C、fibre bandwidth capability between the sites
    • D、number of stacked tape drives attached to each cluster

    正确答案:C

  • 第4题：

    A customer has defined their server needs as a four-LPAR 16-way p570 with 64GB of memory， four 10/100/1000 TX LAN adapters， and six fibre channel adapters to external storage in an IBM ESS （Shark）.  They like the idea of being able to do SAN maintenance while not incurring downtime.  If all LPARs are production related and similar， which question is most appropriate for the pSeries technical specialist to ask？（）

    • A、Would 10/100 Ethernets work as well？
    • B、Should there be eight fibre channel adapters？
    • C、Should there be an async adapter for heartbeat？
    • D、Will all LPARs need access to a common fibre channel tape drive？

    正确答案:B

  • 第5题：

    A customer is ready to order a pSeries solution.  However， the pSeries technical specialist is unsure whether the customer preferred the fibre channel or the external SCSI disk attachment option.  What is the most appropriate action for the specialist to take next？（）

    • A、Ask the customer to confirm which option is best for their environment.
    • B、Order the fibre channel option and purchase a converter later if necessary.
    • C、Order both SCSI and fibre channel adapters to cover both potential options.
    • D、Inform the customer that fibre channel was selected for performance reasons.

    正确答案:A

  • 第6题：

    A customer wants to install an IBM BladeCenter infrastructure but is concerned about the cost of the full fabric internal fibre switches. Consequently, the customer is considering an N_Port ID Virtualization (NPIV) capable switch.Which of the following should be mentioned to the customer regarding the NPIV switch?（）

    • A、You can not use an NPIV switch in the same IBM BladeCenter chassis as a Cisco Intelligent Ethernet Switch 
    • B、Using blade servers with the NPIV switch will require more fibre ports on the external fibre switch 
    • C、Storage devices like Fibre Channel Tape and Disk cannot be attached to the NPIV Switch but must connect to a core fabric switch
    • D、The NPIV switch will count against the number of domains in a fabric

    正确答案:C

  • 第7题：

    A customer has two locations located 7 kilometers apart. The production site has a Cisco 9509chassis with 48 Fibre Channel ports activated， and the disaster recovery site has a Cisco 9509chassis with 48 Ethernet ports activated. Which of the following products will be used to get thedata from one location to the other？（）

    • A、IBM SAN40-B4
    • B、Cisco MDS 9222i
    • C、Cisco MDS 9148
    • D、IBM SAN32B-E4 with encryption

    正确答案:B

  • 第8题：

    单选题
    A customer has two single cluster IBM TS7700 Virtualization Engines at the same site. The customer wants to move one to a remote site and set up a grid configuration with the two clusters. The customer has fibre between the two sites. What is the most important factor to consider when planning the new configuration?（）
    A

    operator training

    B

    cache size of the two clusters

    C

    fibre bandwidth capability between the sites

    D

    number of stacked tape drives attached to each cluster


    正确答案： C
    解析： 暂无解析

  • 第9题：

    单选题
    A manufacturing customer has an IBM BladeCenter H chassis with four， HX5 with MAX5 4-socket blades installed. Each blade has the optional Fibre Channel Expansion card. The customer wants redundancy and is going to install the following configuration：  （1）two Brocade 20-Port SAN Switch Modules  （2）two Nortel Networks 1/10 GB Uplink ESM  （3）a redundant AMM  What is the minimum number of power supplies needed for this configuration to have full redundancy？（）
    A

    4

    B

    3

    C

    2

    D

    8


    正确答案： B
    解析： 暂无解析

  • 第10题：

    单选题
    A customer has provided the pSeries technical specialist with details of an HACMP solution that they would like validated.  The solution is for two POWER4+ p630 servers directly attached to a FAStT600 storage server as the shared storage.  Each system has the following： ？ 2 integrated network ports ？   2 fibre channel adapter cards   ？ 1 power supply and redundant cooling   ？ HACMP v5.1   In addition to a second power supply， what further requirements， if any， are needed to validate this solution and ensure no single point of failure？ （）
    A

    One fibre channel switch

    B

    Two fibre channel switches

    C

    Two Ethernet cards

    D

    Nothing


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    Which statement describes multihop FCoE function when an FCoE switch receives an FCoE frame from the directly connected FCoE host？（）
    A

     The switch receives the FCoE frame and forwards it to another switch over its VE port.

    B

     The switch receives the FCoE frame， deapsulates it， and sends the Fibre Channel frame to the fabric over its Fibre Channel uplink port.

    C

     The switch receives the FCoE frame， deapsulates it， and sends the Fibre Channel frame to the Fibre Channel target over its Fibre Channel port.

    D

     The switch receives the FCoE frame and forwards it to another FCoE device over its VN port.


    正确答案： C
    解析： 暂无解析

  • 第12题：

    单选题
    A customer wants to install an IBM BladeCenter infrastructure but is concerned about the cost of the full fabric internal fibre switches. Consequently， the customer is considering an N_Port ID Virtualization （NPIV） capable switch. Which of the following should be mentioned to the customer regarding the NPIV switch？（）
    A

    Youcan not use an NPIV switch in the same IBM BladeCenter chassis as a Cisco Intelligent Ethernet Switch

    B

    Using blade servers with the NPIV switch will require morefibre ports on the external fibre switch

    C

    Storage devices likeFibre Channel Tape and Disk cannot be attached to the NPIV Switch but must connect to a core fabric switch.

    D

    The NPIV switch will count against the number of domains in a fabric


    正确答案： A
    解析： 暂无解析

  • 第13题：

    A customer has a Fibre Channel switch residing in a configuration where both production and test data coexist. Which of the following is the simplest method for ensuring that the two types of data do not flow through the same port?（）

    • A、VLAN
    • B、zoning
    • C、trunking
    • D、LUN masking

    正确答案:B

  • 第14题：

    A server has lost communication to its drives located on a fiber channel SAN.An administrator notices that the indicator lights on both the HBA and the SAN switch are not lit.Which of the following are the MOST likely causes of the problem？（）

    • A、Failed HBA
    • B、Failed switch port
    • C、Faulty fiber cable
    • D、Faulty driver
    • E、Failed hard drives
    • F、Faulty configuration

    正确答案:A,B,C

  • 第15题：

    Which statement about Cisco Unified Fabric switches is correct？ （）   

    • A、 The Nexus 5000 family of switches does not support vPC when running in either NPV or FCoE NPV mode.
    • B、 The MDS 9100 family of switches is an excellent design choice as a Unified Fabric edge switch. 
    • C、 The Nexus 7000 Series Switches can support the NPIV mode of operation， but cannot function as a complete Fibre Channel Forwarder.
    • D、 The Nexus 7000 Series Switches cannot support advanced Cisco Fibre Channel features such as IVR.
    • E、 The MDS family of Cisco Unified Fabric switches supports both the Fibre Channel Forwarder and Fibre Channel Bridge functions.

    正确答案:E

  • 第16题：

    A system is being planned with three production partitions, one each for an IBM i, AIX standard edition, and Power Linux applications. One fibre-channel attached TS3100 tape library will be shared between the partitions for backup. Which solution provides tape library sharing with minimum operator intervention?（）

    • A、Configure VIO Server Express Edition to control the tape library through one fibre channel card.Assign the  library to the production partitions when needed.
    • B、Configure the IBM i partition to own the tape library.Use IBM i virtualization to host a virtual tape library  connection to the AIX and Linux partition.Assign the library to the production partitions when needed.
    • C、Configure a fibre channel card for each partition， and a configure fibre switch.Connect the partitions and  tape library to the switch.Zone the switch so all partitions can enable the tape when needed and disable  the tape when finished.
    • D、Configure AIX to control the tape library through one fibre channel adapter.Use AIX virtualization to host a  virtual tape library connection to the IBM i and Linux partitions.Assign the library to the production  partitions when needed.

    正确答案:B

  • 第17题：

    A customer is deploying a new database on a PS701 Blade in a BladeCenter H, and requires redundant network and SAN adapters. Which configuration supports the customer requirement?（）

    • A、Configure 2CFFh combination fibre channel / gigabit Ethernet adapters
    • B、Configure 1CFFh 2-port fibre channel adapter and 1 CIOv 2-port gigabit Ethernet adapter
    • C、Configure 1CIOv 2-port fibre channel adapter and 1 CFFh combination fibre channel / gigabit Ethernet  adapter
    • D、Configure 1CIOv 2-port gigabit Ethernet adapter and 1 CFFh combination fibre channel / gigabit Ethernet  adapter

    正确答案:C

  • 第18题：

    A banking customer has the following requirements for an IBM BladeCenter solution with high speed fibre channel： （1）four 4-socket Microsoft SQL servers with two hot swap SAS drives  （2）two physical Microsoft Active Directory Servers  （3）twenty-two physical Citrix servers  （4）three physical Web servers （5）one physical vCenter server   （6）eight vSphere hosts  Which configuration minimally satisfies these requirements？（）

    • A、Three IBMBladeCenter S chassis， three Brocade Fibre modules， six Ethernet modules
    • B、Three IBMBladeCenter E chassis， three Brocade Fibre modules， six Ethernet modules
    • C、Four IBMBladeCenter H chassis， four QLogic Fibre Channel modules， eight Ethernet modules
    • D、Three IBMBladeCenter H chassis， three QLogic Fibre Channel modules， six Ethernet modules

    正确答案:D

  • 第19题：

    A customer is deploying a new database on a PS701 Blade in a BladeCenter H, and requires redundant network and SAN adapters. Which configuration supports the customer requirement?（）

    • A、Configure 2 CFFh combination fibre channel / gigabit Ethernet adapters
    • B、Configure 1 CFFh 2-port fibre channel adapter and 1 CIOv 2-port gigabit Ethernet adapter
    • C、Configure 1 CIOv 2-port fibre channel adapter and 1 CFFh combination fibre channel / gigabit Ethernet adapter
    • D、Configure 1 CIOv 2-port gigabit Ethernet adapter and 1 CFFh combination fibre channel / gigabit Ethernet adapter

    正确答案:C

  • 第20题：

    单选题
    A Fibre Channel fabric （or Fibre Channel switched fabric， FC-SW） is a switched fabric of FibreChannel devices enabled by a Fibre Channel switch. Fabrics are normally subdivided by Fibre Channel zoning. Each fabric has a name server and provides other services. Higher redundancy over FC-AL，P2P.Which path selection protocol is used by Fibre Channel fabrics？（）
    A

     OSPF

    B

     RIP

    C

     FSPF

    D

     VSANs


    正确答案： D
    解析： 暂无解析

  • 第21题：

    单选题
    Which of the following describes the advantage of using Fibre Channel over Ethernet （FCoE） in POWER6 and POWER7 Blades？（）
    A

    The FCoE card provides both LAN and fibre channel function from a single card on the blade. 

    B

    The FCoE advanced technology removes the need for any BladeCenter switching to support this function.

    C

    Component reliability on the fibre channel over Ethernet is higher than on regular Ethernet and fibre channel adapters.

    D

    The AIX device driver for FCoE has been completely rewritten for the current adapter， eliminating errors and performance issues.


    正确答案： B
    解析： 暂无解析

  • 第22题：

    单选题
    In a Cisco Unified Computing System， where are SAN port channels connected to？（）
    A

     Only to Cisco Fibre Channel switches

    B

     Only to Cisco Fibre Channel switches in NPIV mode

    C

     To any Fibre Channel switch

    D

     Directly to storage arrays

    E

     Only to Nexus Switches


    正确答案： E
    解析： 暂无解析

  • 第23题：

    多选题
    A server has lost communication to its drives located on a fiber channel SAN.An administrator notices that the indicator lights on both the HBA and the SAN switch are not lit.Which of the following are the MOST likely causes of the problem？（）
    A

    Failed HBA

    B

    Failed switch port

    C

    Faulty fiber cable

    D

    Faulty driver

    E

    Failed hard drives

    F

    Faulty configuration


    正确答案： A,B,C
    解析： 暂无解析

相关内容