Intheexhibit，youdecidedtochangemyHostsaddresses.[editsecuritypolicies]user@hostshowfrom-zonePrivateto-zoneExternal{policyMyTraffic{match{source-addressmyHosts；destination-addressExtServers；application[junos-ftpjunos-bgp]；}then{permit{tunnel{ipsec-vpnvpnTu

题目

Intheexhibit，youdecidedtochangemyHostsaddresses.[editsecuritypolicies]user@hostshowfrom-zonePrivateto-zoneExternal{policyMyTraffic{match{source-addressmyHosts；destination-addressExtServers；application[junos-ftpjunos-bgp]；}then{permit{tunnel{ipsec-vpnvpnTunnel；}}}}}policy-rematch；Whatwillhappentothenewsessionsmatchingthepolicyandin-progresssessionsthathadalreadymatchedthepolicy？（）

A.Newsessionswillbeevaluated.In-progresssessionswillbere-evaluated.

B.Newsessionswillbeevaluated.Allin-progresssessionswillcontinue.

C.Newsessionswillbeevaluated.Allin-progresssessionswillbedropped.

D.Newsessionswillhaltuntilallin-progresssessionsarere-evaluated.In-progresssessionswillbere-evaluatedandpossiblydropped.

相似考题

1.Click the Exhibit button.In the exhibit, what is the function of the configuration statements?()A. This section is where you define all chassis clustering configuration.B. This configuration is required for members of a chassis cluster to talk to each other.C. You can apply this configuration in the chassis cluster to make configuration easier.D. This section is where unique node configuration is applied.

2.Click the Exhibit button.In the exhibit, which statement is correct? ()A. Three physical interfaces are redundant.B. You must define an additional Redundancy Group.C. node 0 will immediately become primary in the cluster.D. You must issue an operational command and reboot the system for the above configuration to take effect.

3.Click the Exhibit button.In the exhibit, what is the priority for Router B in VRRP group 100?()A.1B.100C.110D.255

4.ClicktheExhibitbutton.Intheexhibit,theprotect－refilterisappliedasaninputfilteronthelo0.0interfaceandallpossibleservicesareenabledunder[editsystemservices].Whichtwomethodscanyouusetoaccesstherouter?()A.FTPB.SSHC.TelnetD.J-Web

更多“Intheexhibit,youdecidedtochangemyHostsaddresses.[editsecuritypolicies]user@hostshowfrom－zo ”相关问题

  • 第1题：

    Click the Exhibit button.In the exhibit, the Compression > Basic > Endpoints page shows an icon of a red "X" under the tunnel status "IN" column. The error message displays, "No Request Received".What does this indicate?（）

    A. There are no devices at the remote site.

    B. The remote side does not have QoS enabled.

    C. The remote side is not configured for compression to this endpoint.

    D. The remote side is not configured for decompression to this endpoint.


    参考答案：C

  • 第2题：

    Click the Exhibit button.In the exhibit, two physical routers are configured for VRRP in the network with WXC devices.How should you define the default gateway address on each WXC device?()

    A. Define the virtual router IP address on both WXC devices.

    B. Add a static route for the virtual router IP address on both WXC devices.

    C. Define the physical IP address of each router on each respective WXC device.

    D. Leave the default gateway field in the WXC device blank; it will automatically detect the active gateway address.


    参考答案：C

  • 第3题：

    Click the Exhibit button. Within an ONS 15454, you are provisioning a circuit on an unprotected UPSR ring. In the exhibit, which two must you configure?() (Choose two.)

    A. revertive

    B. circuit type

    C. circuit size

    D. bidirectional

    E. protected drops

    F. switch on PDI-P


    参考答案：B, C

  • 第4题：

    Click the Exhibit button.In the exhibit, if the link we are measuring is 1.5 Mbps, what is the effective WAN bandwidth?()

    A.0.947 Mbps

    B.3.000 Mbps

    C.4.065 Mbps

    D.282.058 Mbps


    参考答案：C

  • 第5题：

    ClicktheExhibitbutton.WithinanONS15454,youareprovisioningacircuitonanunprotectedSNCPring.Intheexhibit,whichtwomustyouconfigure?()

    A.revertive

    B.circuitsize

    C.circuittype

    D.bidirectional

    E.protecteddrops

    F.SwitchonPDI-P


    参考答案：B, C

相关内容