Which command prompts an ERX Edge Router to go into a loopback mode on T1 number 1 when a command is received from a remote ERX Edge Router?()A.AB.BC.CD.D

题目
Which command prompts an ERX Edge Router to go into a loopback mode on T1 number 1 when a command is received from a remote ERX Edge Router?()

A.A

B.B

C.C

D.D

相似考题

1.当一个GPRS用户使用EDGE终端时:()A.就能使用EDGE服务B.只有在EDGE小区才能使用EDGE服务C.只有在EDGE小区并且占用的是EDGE信道才能使用EDGE服务D.在申请开通EDGE业务成功后才能使用

2.The output of the show aaa domain-map displays the following information:Domain: isp1.com; virtual-router: vr1; loopback: 1Domain: isp2.com; virtual-router: vr2; loopback: 1Domain: none; virtual-router: vr3; loopback: 1Domain: default; virtual-router: vr4; loopback: 1The end user supplies a login name of joe@isp7.com .Which virtual router is responsible for authenticating this user?（）A. vr1B. vr2C. vr3D. vr4

3.下面是路由器Router1的配置命令列表，在空白处填写合适的命令/参数，实现Router1的正确配置。Router1＞enRouter1conf termRouter1(config)iriterface e0Router1(config-if)ip address 192.1.0.129 255.255.255.192Router1 (config-if)interface s0Router1(config-if)ip address 192.200.10.5 255.255.255.252Router1(config-if)endRouter1(config)Eouter (5)Router1(config-router)network (6) area 0Router1(config-router)network (7) area 1Router1(config-router)exitRouter1copy run start

4.下面是路由器Router1的配置命令列表，请为(6)～(10)空缺处填写合适的命令/参数，实现Router1的正确配置。Router＞enableRouter config terminalRouter (config) hostname Router1Router1 (config) interface ethernet 0Router1 (config-if) ip address (6)Router1 (config-if) no shutdownRouter1 (config-if) (7)Router1 (config-if) ip address (8)Router1 (config-if) no shutdownRouter1 (config-if) exitRouter1 (config) ip routingRouter1 (config) router ospf 100Router1 (config-router) (9)Router1 (config-router) (10)Router1 (config-router) ip ospf message-digest-key 1 md 5 wg_gczRouter1 (config-router) area 0 authentication message-digestRouter1 (config-if) endRouter1 Copy run start

参考答案和解析
参考答案：A
更多“Which command prompts an ERX Edge Router to go into a loopback mode on T1 number 1 when a command is received from a remote ERX Edge Router?() ”相关问题

  • 第1题：

    WhichofthefollowingcommandsonthewirelessinterfaceofaCisco3845IntegratedService RouterallowstheSSIDtobroadcast?()

    A.router（config-ssid）#enable

    B.router（config-ssid）#advertise

    C.router（config-ssid）#broadcast

    D.router（config-ssid）#guest-mode


    参考答案：D

  • 第2题：

    Refer to the exhibit. What will Router1 do when it receives the data frame shown?()

    A.Router1 will strip off the source MAC address and replace it with the MAC address 0000.0c36.6965.

    B.Router1 will strip off the source IP address and replace it with the IP address 192.168.40.1.

    C.Router1 will strip off the destination MAC address and replace it with the MAC address 0000.0c07.4320.

    D. Router1 will strip off the destination IP address and replace it with the IP address of 192.168.40.1.

    E.Router1 will forward the data packet out interface FastEthernet0/1.

    F.Router1 will forward the data packet out interface FastEthernet0/2.


    参考答案：A, C, F

  • 第3题：

    小区内EDGE分组信道和非EDGE分组信道可以共存,优先为EDGE手机分配EDGE信道,为GPRS手机分配非EDGE信道。

    A．错误

    B．正确


    参考答案：A

  • 第4题：

    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? ()

    A.Router1 has specific boot system command that instruct it to load IOS from TFTP server.

    B.Router1 is acting as a TFTP server for other routers.

    C.Router1 cannot locate a valid IOS image in flash memory.

    D.Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

    E.Cisco routers will first attempt to load a image from TFTP for management purposes.


    参考答案：A, C

  • 第5题：

    关于动态路由协议中的路由ID描述错误的是()

    A.如果使用router-id命令手工配置router-id，就使用该router-id

    B.如果没有手工配置router-id并且配置了loopback接口地址，则选了loopback接口地址最大的作为router-id

    C.如果没有配置router-id且米有配置loopback接口地址，则从其物理接口的IP地址中选择最大的作为router-id

    D.Router-id改变之后，各个协议的router-id就会改变，不需要额外的操作


    参考答案：D

  • 第6题：

    某华为路由器的名称为Router1，系统视图的提示符是 。

    A．%Router1%

    B．＜Router1＞

    C．[Router1]

    D．#Router1#


    [Router1]

相关内容