Why would the Ezonexam administrator change the value of the spanning-tree priority of a switch?
A. in order to optimize the path that frames take from source to destination
B. to increase the priority so a designated port will become a root port
C. to increase the BID, so the switch is more likely to become root bridge
D. in order to allow VLANs to be sent from one switch to another across a single link
E. to force a given switch to become an STP server
F. None of the above
第1题:
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network?()
A. Lower the bridge priority number.
B. Change the MAC address of the switch.
C. Increase the VTP revision number for the domain.
D. Lower the root path cost on the switch ports.
E. Assign the switch an IP address with the lowest value.
第2题:
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology?()
第3题:
What value is primarily used to determine which port becomes the root port on each non root switch in a spanning-tree topology?()
第4题:
RSTP根端口的根路径优先级向量(Root Path Priority Vector)和根端口的端口优先级向量(Port Priority Vector)相同。()
第5题:
Each port that is configured to use LACP has an LACP port priority. Which statements are true about LACP port priority? ()
第6题:
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network?()
第7题:
The designated port is the switch port on every nonroot bridge that is the chosen path to theroot bridge. There can be only one designated port on every switch. The designated portassumes the forwarding state in a stable active topology. All switches connected to a given segment listen to all BPDUs and determine the switch that will be the root switch for a particular segment.
The disabled port is an additional switch port on the designated switch with a redundant link to the segment for which the switch is designated. A disabled port has a higher port ID than the disabled port on the designated switch. The disabled port assumes the discarding state in astable active topology.
The backup port is a switch port that offers an alternate path toward the root bridge. The backup port assumes a discarding state in a stable, active topology. The backup port will be present on nondesignated switches and will make a transition to a designated port if the current designated path fails.
The root port is the switch port on every nonroot bridge that is the chosen path to the root bridge. There can be only one root port on every switch. The root port assumes the forwarding state in a stable active topology.
第8题:
in order to optimize the path that frames take from source to destination
to increase the priority so a designated port will become a root port
to increase the BID, so the switch is more likely to become root bridge
in order to allow VLANs to be sent from one switch to another across a single link
to force a given switch to become an STP server
第9题:
lowest port MAC address
port priority number and MAC address.
VTP revision number
highest port priority number.
path cost
第10题:
lowest port MAC address
port priority number and MAC address.
VTP revision number
highest port priority number.
pathcost
第11题:
BPDU guard can be used to prevent invalid BPDUs from propagating throughout the network.
BPDU guard can guarantee proper selection of the root bridge.
BPDU guard can be utilized to prevent the switch from transmitteing BPDUs and incorrectly altering the root bridge election.
BPDU guard can be utilized along with PortFast to shut down ports when a switch is connected to the port.
None of the other alternatives apply
第12题:
Port priority value can be configured between 1 and 65535.
A higher port priority value means a higher priority of LACP.
Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.
LACP uses the port priority with the port number to form the port identifier.
LACP Port priority default value should always be changed
第13题:
A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge()。
A.Establish a direct link from the switch to all other switches in the network.
B.Assign the switch a higher MAC address than the other switches in the network have.
C.Configure the switch so that it has a lower priority than other switches in the network.
D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.
E.Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.
第14题:
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-treetopology?()
第15题:
Why would an administrator change the value of the spanning-tree priority of a switch?()
第16题:
What value is primarily used to determine which port becomes the root port on each nonroot switch in aspanning-tree topology?()
第17题:
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology?()
第18题:
Which statement is correct about RSTP port roles?()
第19题:
Lower the bridge priority number.
Change the MAC address of the switch.
Increase the VTP revision number for the domain.
Lower the root path cost on the switch ports.
Assign the switch an IP address with the lowest value.
第20题:
Lower the bridge priority number.
Change the MAC address of the switch.
Increase the VTP revision number for the domain.
Lower the root path cost on the switch ports.
Assign the switch an IP address with the lowest value.
第21题:
lowest port MAC address
port priority number and MAC address.
VTP revision number
highest port priority number.
path cost
第22题:
lowest port MAC address
port priority number and MAC address
VTP revision number
highest port priority number
path cost
第23题:
path cost
lowest port MAC address
VTP revision number
highest port priority number
port priority number and MAC address