Using the WLSE, you are trying to push out a configuration job to a standalone access point, butthe job does not start. Which of the following would cause this failure?()
第1题:
A.WCS
B.WLSE
C.LocationAppliance
D.WDS
E.WLSE-Express
第2题:
What management tool could be used to provide centralized configuration, monitoring, and management in a network built on Cisco wireless LAN controllers and Lightweight APs? ()
第3题:
Which two of these statements best describe fast secure roaming for the wireless core feature set using autonomous access points? (Choose two.) ()
第4题:
Which three statements are true about implementing wireless LANs in the Company network using Cisco devices?()
第5题:
Which two statements about the WLAN Solution Engine (WLSE) are true?()
第6题:
On the WLSE or WLSE Express, which of the following criteria for applying automanaged configurations can be combined?()
第7题:
Using the WLSE,you are trying to push out a configuration job to an access point,but the job doesnot start. Which of the following would cause this failure?()
第8题:
When using the WLSE to verify RF coverage, which task will use the configured radio settings?()
第9题:
To support fault and policy reporting, the WLSE requires a Wireless Control System (WCS).
When WLSE detects an AP failure, it automatically increases the power and cell coverage of nearby APs.
WLSE requires the 2700 location appliance to offer location tracking.
WLSE can locate rogue APs and automatically shut them down.
WLSE configuration is done using the command line interface (CLI) or a WEB based template.
第10题:
CiscoWorks Wireless LAN Solution Engine (WLSE)
CiscoWorks Wireless LAN Solution Engine (WLSE) Express
Cisco Wireless Control System (WCS)
Wireless Domain Services (WDS)
WLAN Controllers (WLC)
第11题:
the snmp communities on the switch do not match the wlse.
the snmp communities on the access points do not match the wlse.
the snmp communities on the access points do not match the switch.
the snmp communities on the router do not match the wlse.
第12题:
to support fault and policy reporting, the WLSE requires a Wireless Control System (WCS)
when WLSE detects an AP failure, it automatically increases the power and cell coverage of nearby APs
WLSE requires the 2700 location appliance to offer location tracking
WLSE can locate rogue APs and automatically shut them down
WLSE configuration is done using the command line interface (CLI) or a WEB based template
第13题:
A.configurationofAPs
B.autodiscoveryofrogueAPs
C.reporting
D.WLSEintwoversions:baseandlocation
E.graphicalviewofmultiplecontrollersandmanagedAPs
第14题:
You are trying to deploy a configuration job to an ios access point using the wlse, but the job fails. Which of the following would cause this failure?()
第15题:
Which two statements regarding the Wireless LAN Solution Engine (WLSE) are true? ()
第16题:
Which two statements regarding the Wireless LAN Solution Engine (WLSE) are true?()
第17题:
You are conducting a cdp-based discovery using an edge switch for the seed. there is a router between the switch and the wlse. none of the access points are discovered, and the discovery log shows the switch is snmp unreachable. What is the problem?()
第18题:
Which two statements regarding the Wireless LAN Solution Engine (WLSE) are true ?()
第19题:
On the wlse, radio management must be enabled to use most of the features of which one of the following?()
第20题:
Which two features are supported by the WLAN Solution Engine (WLSE)?()
第21题:
SNMP communities
Telnet/SSH user/password
WLCCP credentials
HTTP user/password
第22题:
It is compatible with all wireless clients.
It reduces roaming latency through reduced client RF channel scanning enhancements.
It reduces roaming latency to targeted times of less than 75ms.
Roaming occurs without reauthentication through a centralized RADIUS server.
It is enabled through WLSE deployment.
第23题:
To support fault and policy reporting,the WLSE requires a Wireless Control System (WCS).
When WLSE detects an AP failure,it automatically increases the power and cell coverage of nearbyAPs.
WLSE requires the 2700 location appliance to offer location tracking.
WLSE can locate rogue APs and automatically shut them down.
WLSE configuration is done using the command line interface (CLI) or a WEB based template.