A BGP router should use three export policies named add-communities, no-rfc1918-routes, andrejected-unwanted. Which export statement places the add-communities policy immediately before the default BGP policy?()
第1题:
In BGP, we can use Route Reflector and full mesh. Why should we use these?
第2题:
You have a router running BGP for the MPLS network and OSPF for the local LAN network at the sales office. A route is being learned from the MPLS network that also exists on the OSPF local network. It is important that the router chooses the local LAN route being learned from the downstream switch running OSPF rather than the upstream BGP neighbor. Also, if the local OSPF route goes away, the BGP route needs to be used. What should be configured to make sure that the router will choose the LAN network as the preferred path?()
第3题:
A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values. Which statement is true about how BGP would select the best path?()
第4题:
Two routers configured to run BGP have been connected to a firewall, one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer, including the correct BGP session endpoint addresses and the correct BGP session hop-count limit (EBGP multihop). What is a good first test to see if BGP will work across the firewall?()
第5题:
Router 1 is configured for BGP as dual-homed on the Cisco network. Which three BGP attributes are carried in every BGP update on this router (both IBGP and EBGP)?()
第6题:
Which three protocols should be explicitly managed by using a CoPP policy on an Internet border router?()
第7题:
The router will use the static route.
The router will use the OSPF route.
The router will use the EIGRP route.
The router will load balance and use all three routes.
第8题:
SMTP
ICMP
BGP
SSH
RTP
BitTorrent
VTP
第9题:
On the CE router, PE neighbors must be configured in the VRF context on the CE router
On PE routers, the CE IBGP neighbors are configured in the global BGP configuration
On PE routers, the CE EBGP neighbors are configured in the VRF context
A separate BGP process must be used on the PE routers for CE routers so that they do not use the same BGP routing process as that used for the PE router's other provider neighbors
第10题:
第11题:
The router will use the static route.
The router will use the OSPF route.
The route will use the EIGRP route.
The router will load balance and use all three routes.
第12题:
origin
router-ID
AS-path
local-preference
next-hop
第13题:
A company has a BGP network and a BGP route of 196.27.125.0/24 that should be propagated toall of the devices. The route is not now in any of the routing tables. The administrator determinesthat an access list is the cause of the problem. The administrator changes the access list to allowthis route, but the route still does not appear in any of the routing tables. What should be done topropagate this route?()
第14题:
When BGP is used as the PE-CE routing protocol, which of these statements is correct?()
第15题:
SR7750调测BGP邻居状态变化的命令是()
第16题:
A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?()
第17题:
Which three statements about the route target (RT) are true? ()
第18题:
Attempt to TELNET from the router connected to the inside of the firewall to the router connected to theoutside of the firewall. If telnet works, BGP will work, since telnet and BGP both use TCP to transportdata.
Ping from the router connected to the inside interface of the firewall to the router connected to theoutside interface of the firewall. If you can ping between them, BGP should work, since BGP uses IP totransport packets.
There is no way to make BGP work across a firewall without special configuration, so there is no simpletest that will show you if BGP will work or not, other than trying to start the peering session.
There is no way to make BGP work across a firewall.
第19题:
You should use Basic authentication on Exchange ActiveSync and set up only Basic authentication on the RPC virtual directory.
You should use NTLM authentication on the RPC virtual directory.
You should use Microsoft Challenge Handshake Authentication Protocol version 2 (MS-CHAP v2) on XXX-EX01.
You should use the anonymous setting in the authentication type for the Microsoft-Server-ActiveSync virtual directory on XXX-EX01.
第20题:
To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50
Th e router will prefer the shortest autonomous system path
If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MED
The router will prefer the route with the lower MED
第21题:
LDAP
ICMP
RTP
BGP
SSH
RDP
第22题:
export [add-communities no-rfc1918-routes ejected-unwanted];
export [no-rfc1918-routes add-communities rejected-unwanted];
export [add-communities rejected-unwanted no-rfc1918-routes];
export [no-rfc1918-routes rejected-unwanted add-communities];
第23题:
[edit protocols bgp group external] user@router# set interfaces ge-0/0/0.42
[edit protocols bgp group external] user@router# edit show interfaces ge-0/0/0.42
[edit protocols bgp group external] user@router# top show interfaces ge-0/0/0.42
[edit protocols bgp group external] user@router# show interfaces ge-0/0/0.42
第24题:
Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works, BGP will work, since telnet and BGP both use TCP to transport data.
Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them, BGP should work, since BGP uses IP to transport packets.
There is no way to make BGP work across a firewall without special configuration, so there is no simple test that will show you if BGP will work or not, other than trying to start the peering session.
There is no way to make BGP work across a firewall.