在锐捷交换机上配置Trunk接口时,出于安全的需要,要禁止VLAN15的数据帧通过,使用的命令是()
第1题:
阅读下面配置信息,解释(9)~(11)处的命令,将答案填写在相应的位置。
SW1>enable (进入特权模式)
SW1(config)interface f0/23 (进入接口23配置模式)
SW1(config-if)switchport mode trunk (9)
SW1(config-if)switchport trunk encaps isl (10)
SW1(config-if)spanning-tree vlan 1 port-priority 10 (11)
SW1(config-if)spanning-tree vlan 2 port-priority 10
SW1(config-if)spanning-tree vlan 3 port-priority 10
SW1(config-if)interface f0/24 (进入接口24配置模式)
SW1(config-if)…….. (对端口24进行配置)
SW1(config-if)end
SW1copy run start
第2题:
A.ruijie(config)#
B.ruijie(config)@
C.ruijie(config)¥
D.ruijie(config)%
第3题:
A.Switch(config-if)#swithcport trunk allowed remove 99
B.Switch(config-if)#swithcport trunk native99
C.Switch(config-if)#swithcport trunk nativevlan99
D.Switch(config-if)#switchport mode trunk
第4题:
A.Router(config-if)#ipaddress210.64.202.23
B.Router(config-if)#ipaddress210.64.202.23255.255.0.0
C.Router(config-if)#ipaddress210.64.202.23/0
D.Router(config-if)#ipaddress210.64.202.23255.255.255.0
第5题:
A.(config-if)#authenticationpppchapfallbackppp
B.(config-if)#authenticationpppchappap
C.(config-if)#pppauthenticationchappap
D.(config-if)#pppauthenticationchapfallbackppp
第6题:
配置策略路由时,需要在接口下通过路由图名字调用已配置的route-map,路由器上有个route-map的名字叫abc,下列配置中正确的是()
第7题:
在骨干网络链路中,为使接入交换机获得高带宽,经常需要把网络的骨干链路进行聚合。在锐捷交换机中,哪条命令可以把一个端口加入到聚合组20中?()
第8题:
在小型分支机构中,出于成本原因,可能会使用路由器子接口互联多个VLAN。下面哪一条命令,可以正确的为VLAN5定义一个子接口?()
第9题:
Which set of commands is recommended to prevent the use of a hub in the access layer?()
第10题:
You need to configure a new Company switch for trunking. Which switch command enables a trunking protocol that appends a four byte CRC to the packet?()
第11题:
Switch(config-if)#swithcport trunk allowed remove 99
Switch(config-if)#swithcport trunk native99
Switch(config-if)#swithcport trunk nativevlan99
Switch(config-if)#switchport mode trunk
第12题:
R2(config-if)#shutdown
R2(config-if)#no tdown
R2(config-if)#block
R2(config-if)#no block
第13题:
下列路由器命令中用于激活接口的命令是(69)。
A.Router(config-if)#noshutdown
B.Router(config-if)#end
C.Router(config-if)#config t
D.Router(config-if)#switchport mode access
第14题:
下面是交换机完成Trunk的部分配置,请根据题目要求,完成下列配置。
SwitchA(config)interface f0/3(进入端口3配置模式)
SwitchA(config-if)switchporl(6)(设置当前端口为Trunk模式)
SwitchA(config-if)sritchport trunk allowed(7)(设置允许所有Vlan通过)
SwitchA(config-if)exit
SwitchA(config)exit
Switch%
第15题:
阅读下面的配置信息,解释(5)处的命令。
Switch
Switchconfig
Switch(config)interface f0/1(进入接口1配置模式)
Switch(config-if)switchport mode trunk(5)
Switch(config-if)switchpoft trunk allowed vlan all(设置允许从该接口交换数据的VLAN)
Switch(config-if)exit
Switch(config)exit
SwitCh
第16题:
A、Switch(config-if)#switchport mode access
B、Switch(config-if)#switchport dynamic auto
C、Switch(config-if)#switchport mode trunk
D、Switch(config-if)#switchport mode dynamic
第17题:
A.switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1
B.switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1
C.switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1
D.switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1
第18题:
能够在CiscoIOS软件中正确地将端口配置为ISL封装的命令是()。
第19题:
配置RLDP防环路的配置有()
第20题:
网络管理员想了解核心交换机的下联端口,是否启用端口聚合,聚合了哪些端口。以下哪个命令可以查看现有聚合组中的成员?()
第21题:
下列路由器命令中用于激活接口的命令是()。
第22题:
Switch(config-if)#Switchport trunk allowed remove 5
Switch(config-if)#Switchport trunk remove 5
Switch(config-if)#Switchport trunk Vlan allowed remove 5
Switch(config-if)#Switchport trunk allowed Vlan remove 5
第23题:
Switch-3548(config-if)#switchport trunk encapsulation dotlq
Switch-3548(config-if)#switchport trunk allowed vlan 1,10,20,30
Switch-3548(config-if)#switchport mode trunk
Switch-3548(config-if)#switchport trunk encapsulation isl
Switch-3548(config-if)#switchport tnmk allowed vlan 1-30
Switch-3548(config-if)#switchport mode trunk
Switch-3548(config-if)#switchport trunk encapsulation negotiate
Switch-3548(config-if)#switchport trunk allowed vlan 1-30
Switch-3548(config-if)#switchport mode trunk
Switch-3548(config-if)#switchport trunk encapsulation dotlq
Switch-3548(config-if)#switchport trunk allowed vlan 1,10,20,30