Provider Core (P)
Provider Edge (PE)
Customer Edge (CE)
Customer Boundary (CB)
第1题:
When implementing MPLS VPNs between CE and PE routers, which of these statements is correct?As a Network Engineer, it is necessary for you to know how to implement MPLS VPNs between Customer Edge and Provider Edge routers.Refer to the following descriptions, which one is making sense?()
A. If using OSPF or EIGRP as the PE-CE routing protocol, redistribution is not required, but any other protocol or static route will require redistribution
B. If using IS-IS as the PE-CE routing protocol, no redistribution is required
C. If using static routes between the CE and PE routers, no redistribution of other VPN routes is required
D. If PE-CE protocol is not BGP, redistribution of other VPN routes from MP-BGP is required
第2题:
Which configuration command allows the ERX Edge Router to advertise customer networks into the provider’s IGP?()
第3题:
Which four statements about the Carrier Supporting Carrier (CSC) feature are true? ()
第4题:
Which VPN router does not contain customer routing knowledge?()
第5题:
What configuration command allows the ERX Edge Router to advertise customer networks into the provider’s IGP?()
第6题:
Which two statements about Layer 3 MPLS VPN are true?()
第7题:
In a bridged 1483 network,which configuration command allows the ERX Edge Router to advertise customer networks into the provider's IGP?()
第8题:
MPLS is required between the PE and CE routers that connect the backbone carrier to the customer carrier.
The backbone carrier must enable the PE router to check that the packets it receives from the CErouter contain only the labels that the PE router advertised to the CE router.
Every packet that crosses the backbone carrier must be encapsulated so that the packet includes MPLS labels
AII PE routers that link the backbone carrier to the customer carrier must run Route Target Rewrite.
Arouting protocol is required between the PE and CE routers that connect the backbone carrierto thecustomer carrier. The routing protocol enables the customer carrier to exchange IGP routing information with the backbone carrier.
第9题:
A sham-link is created between any twoo VPN sites that belong to the same OSPF area and share an OSPF backdoor link
A sham-link is seen as an intra-area link between PE routers,an OSPF adjacency is created and data base is exchanged
A SHAM link is created between two directly connected PE routers so that it is preferred over the low speed backdoor door
A SHAM link is part of OSPF network of MPLS-VPN provider
第10题:
redistribute direct
redistribute static
redistribute connected
redistribute access-internal
第11题:
The virtual routing and forwarding table is separate from the global routing table that exists on PE routers. Routes are injected into the VRF from the CE-PE routing protocols for that VRF and any MP-BGP announcements that match the defined VRF RTs
Multiprotocol Border Gateway Protocol is run between PE and CE routers to exchange customer prefixes in a VPNv4 format
A customer edge router peers at Layer 3 to the provider edge. The PE-CE interface runs either a dynamic routing protocol (eBGP, RIPv2, EIGRP, OSPF) or a static routing protocol (Static, Connected)
VPNv4 address is the combination of the RT and customer IPv4 prefix. These VPNv4 prefixes are passed in MP-BGP
第12题:
redistribute direct
redistribute static
redistribute connected
redistribute access-internal
第13题:
If the OSPF protocol is used to connect customer edge (CE) routers to service provider edge(PE) routers in the VPN backbone, which two options best describe the use of SHAM links?()
第14题:
When implementing MPLS VPNs between CE and PE routers, which of these statements is correct? As a Network Engineer, it is necessary for you to know how to implement MPLS VPNs between Customer Edge and Provider Edge routers. Refer to the following descriptions, which one is making sense?()
第15题:
What does the OSPF command capability vrf-lite achieve?()
第16题:
Which type of VPN router is not required to run MPLS?()
第17题:
Which statement about implementing the Cisco IPv6 provider Edge Router over MPLS is true?()
第18题:
In a bridged 1483 network, what configuration command allows the ERX Edge Router to advertise customer networks into the provider’s IGP? ()
第19题:
Provider Core (P)
Provider Edge (PE)
Customer Edge (CE)
Customer Boundary (CB)
第20题:
Provider Core (P)
Provider Edge (PE)
Customer Edge (CE)
Customer Boundary (CB)
第21题:
redistribute direct
redistribute static
redistribute connected
redistribute access-internal
第22题:
redistribute direct
redistribute static
redistribute connected
redistribute access-internal
第23题:
It enables provider edge (PE) specific checks on a router when the OSPF process is associated with the VRF
It disables provider edge (PE) specific checks on a router when the OSPF process is associated with the VRF
It enables the exchange of the VRF-Lite capability when the OSPF adjacency is formed.
It disables the MPLS processing on the OSPF learned routes inside the VRF
第24题:
If using OSPF or EIGRP as the PE-CE routing protocol, redistribution is not required, but any other protocol or static route will require redistribution
If using IS-IS as the PE-CE routing protocol, no redistribution is required
If using static routes between the CE and PE routers, no redistribution of other VPN routes is required
If PE-CE protocol is not BGP, redistribution of other VPN routes from MP-BGP is required