A.Enable VTP pruning
B.From privileged mode,erase the startup configuration file,then reload.
C.From privileged mode,erase the vlan date file,then reload.
D.Cycle the switch power.
第1题:
A.Enable VTP pruning
B.From privileged mode,erase the startup configuration file,then reload.
C.From privileged mode,erase the vlandate file,then reload.
D.Cycle the switch power.
第2题:
As witch is configured as a vtp sever with a domain name of CCNA.Which cisco ios privileged mode command,followed by a reload of the swith,will reset the VTP management domain name of the switch to a NULL value?()
第3题:
A switch is configured as a vtp sever with a domain name of CCNA.Which cisco ios privileged mode command,followed by are load of the swith,will reset the VTP management domain name of the switch to a NULL value?()
第4题:
What are two characteristics of a switch that is configured as a VTP client?()
第5题:
Assuming default setting,how can you erase the VTP data base of VLANs on a CISCO IOS switch running in VTP server mode?()
第6题:
Which VTP mode should a Cisco switch be set to if this switch is to add or delete VLANs to a management domain?()
第7题:
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link?()
第8题:
A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration?()
第9题:
#vtp domain unset
#delete vlan.dat
#novtp domain
#vtp domain null
第10题:
Configure the switch to be in VTP client mode.
Configure the switch to be in VTP domaint mode.
Configure the switch to be in VTP transparent mode.
Configure the switch to be in VTPv2.
第11题:
Transparent
Server
Auto
Client
User
第12题:
As witch is configured as a vtp sever with a domain name of CCNA.Which cisco ios privileged mode command,followed by a reload of the swith,will reset the VTP management domain name of the switch to a NULL value?()
A.#vtp domain unset
B.#delete vlan.dat
C.#no vtp domain
D.#vtp domain null
第13题:
A switch that is to be added to the production network has been preconfigured (trunks, VLANs, VTP, and STP) and was tested in your lab. After installing the switch into the network, the entire network went down. What might explain what happened? ()
第14题:
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?()
第15题:
A switch is configured as a vtp sever with a domain name of CCNA.Which cisco ios privileged mode command,followed by a reload of the swith,will reset the VTP management domain name of the switch to a NULL value?()
第16题:
Assuming default setting,how can you erase the VTP database of VLANs on a CISCO IOS switch running in VTP server mode?()
第17题:
What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?()
第18题:
Before inserting a new switch in the network,the network administrator checks that the VTP domain name is correct,the VTP mode is set to server, and revision is lower than the switches in the network. The administrator then configures interfaces and trunks,erases existing VLANs,and connects the switch to the network. Following that procedure,there is no connectivity in the network. What is a possible cause of this problem?()
第19题:
The new switch happened to be running Cisco Catalyst operating system, while the other network switches were running Cisco IOS Software.
The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.
The link costs on the new switch are set to a high value, causing all ports on the new switch to go into a forwarding mode and none into blocking mode, thereby causing a spanning-tree loop.
The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
第20题:
if a switch that is configured to operate in client mode cannot access a VTP server,then the switch reverts to transparent mode.
The local vlan configuration is updated only when an update that has a higher configuration revision number is received.
Vtp advertisements are not forwarded to neighboring switches that are configured in vtp transparent mode.
When switches in vtp client mode are rebooted,they send a vtp advertisement request to the vtp servers.
Vtp client is the default vtp mode
On switches that are configured to operate in client mode ,vlans can be created,deleted,or renamed locally
第21题:
#vtp domain unset
#delete vlan.dat
#no vtp domain
#vtp domain null