A. To ma a known IP address to a MAC address
B. To map a known DLCI to a MAC address
C. To ma a known MAC address to an IP address
D. To ma a known DLCI address to a IP address
E. To ma a known IP address to a SPID address
F. To ma a known SPID address to a MAC address
第1题:
A. Inverse-ARP
B. Reverse-ARP
C. Proxy ARP
D. ARP
第2题:
A. frame-relay arp
B. frame-relay map
C. frame-relay interface-dlci
D. frame-relay lmi-type
E. frame-relay pvc
第3题:
Select the 3 best answers describing operation and configuration of Frame-Relay Inverse ARP.()
第4题:
A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?()
第5题:
What is the purpose of the inverse ARP?()
第6题:
The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?()
第7题:
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()
第8题:
在封装了帧中继协议的接口上使能动态逆向地址解析协议的命令是()。
第9题:
The Serial0/0 interface is passing traffic.
The DLCI 100 was dynamically allocated by the router
The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP server
The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud
The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
第10题:
Static mapping is used when the remote router does not support Inverse ARP.
Frame Relay Inverse ARP requires LMI capability to construct an address to the DLCI mapping tableon the router.
Frame Relay Inverse ARP is disabled by default in Cisco IOS Software for all protocols that areenabled on the physical interface.
Inverse ARP does not work when LMI is disabled.
Frame Relay provides forward and backward congestion notification messages
第11题:
Needs to use Inverse ARP.
Maps a single IP subnet per DLCI.
Maps a single IP subnet across multiple DLCIs.
Resolves NBMA (non broadcast multi access) split horizon issues.
Requires use of the frame-relay map command.
None of the above
第12题:
Dynamic address mapping uses Frame Relay Inverse ARP to request the next-hop protocol address for a specific connection on its known DLCI
Responses to Inverse ARP requests are entered in an address-to-DLCI mapping table on the router or access server which is used to supply the next-hop protoco address or the DLCI for outgoing traffic
Inverse ARP is enabled by default for all protocols enabled on the physical interface
Inverse ARP is configured using the following command under the Interface configuration ’frame-relaymap dlci (dlci number) protocol protocol-address’
Inverse ARP in Frame-Relay is synonymous of ARP in Ethernet
第13题:
The Testking Central and Remote offices are configured as shown below:The remote router can be successfully pinged from the central office but the remote users can‘t access the server at the central office.Based on the output above, what do you suspect is the cause of this problem?()
A. The Frame Relay PVC is down.
B. The IP addressing on the Central/Remote serial link is incorrect.
C. RIP routing information is not being forwarded.
D. Frame Relay inverse-ARP is not properly configured.
第14题:
A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly
第15题:
Which statement about Frame Relay is not true?()
第16题:
Inverse ARP is being used in the TestKing frame relay network. What is the purpose of Inverse ARP?()
第17题:
在封装了帧中继协议的接口上使能动态逆向地址解析协议的命令是:()
第18题:
Refer to the exhibit. What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?()
第19题:
Which of the following processes, is used to find the hardware address of a LAN device?()
第20题:
frame-relay arp
frame-relay map
frame-relay interface-dlci
frame-relay lmi-type
第21题:
To ma a known IP address to a MAC address
To map a known DLCI to a MAC address
To ma a known MAC address to an IP address
To ma a known DLCI address to a IP address
To ma a known IP address to a SPID address
To ma a known SPID address to a MAC address
第22题:
frame-relay arp
frame-relay map
frame-relay interface-dlci
frame-relay lmi-type
frame-relay pvc
第23题:
Enable Proxy ARP.
Disable Proxy ARP.
Enable Inverse ARP.
Disable Inverse ARP.