What will cause a Ezonexam router to enter setup mode? (Choose two)A. The configuration file is missing in NVRAM.B. The configuration register is set to 0x2100.C. Boot system commands are misconfigured in the running-configuration.D. The setup command was

题目

What will cause a Ezonexam router to enter setup mode? (Choose two)

A. The configuration file is missing in NVRAM.

B. The configuration register is set to 0x2100.

C. Boot system commands are misconfigured in the running-configuration.

D. The setup command was issued from the privileged mode prompt.

E. The IOS is missing.

F. The IOS is corrupt.

相似考题

1.What will a new Ezonexam router do during startup if a configuration file is not located in NVRAM?A．It will search for the configuration file in the locations specified by boot system commands.B．It will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D．It will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.

2.Why might the Ezonexam network administrator set the configuration register to 0x2142 on a 2600 series Cisco router?A．To boot the IOS from ROMB．To reset the console passwordC．To upload a new version of the configuration fileD．To upload a new version of the IOSE．To allow a new memory upgrade to be recognized by the router

3.What does a configuration Register Setting of 0x2105 indicate to the Router? ()A. The Boot IOS Code is Located in the NVRAM.B. Check NVRAM for boot system Commands.C. Bypass NVRAM Configurations.D. Boot the IOS Code Located in ROM.E. Perform a Password Recovery.F. Bypass The Code In ROM.

4.You are a senior network administrator at Ezonexam, and while performing the password recovery procedure on your 2500 series Cisco router, you type in the following command:o/r 0x2142What is the purpose of this command?A．It is used to restart the router.B．It is used to bypass the configuration in NVRAM.C．It is used to enter ROM Monitor mode.D．It is used to view the lost password.E．It is used to save the changes to the configuration.

更多“What will cause a Ezonexam router to enter setup mode? (Choose two)A. The configuration file is missing in NVRAM.B. The configuration register is set to 0x2100.C. Boot system commands are misconfigured in the running-configuration.D. The setup command was”相关问题

  • 第1题：

    What is the purpose of pressing the Ctrl＋Break keys during the router password recover procedure?()

    A. To restart the router.

    B. To bypass the configuration in Flash.

    C. To view the password before changes are made.

    D. To bypass setup configuration mode.

    E. To access ROM Monitor mode.


    参考答案：E

  • 第2题：

    A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file.Which command will display this information, and what is the configuration register value that should be displayed?（）

    A. show startup-config and 0x2142

    B. show version and 0x2102

    C. show flash and 0x2102

    D. show version and 0x2142

    E. show running-config and 0x2142

    F. show flash and 0x2142


    参考答案：B

  • 第3题：

    Exhibit: The following are true with one of the TestKing routers:1) The IOS image in flash is missing2) No Network connectivity is available.3) The router fallback IOS image is corrupt.How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）

    A. The router will enter setup mode.

    B. The router will enter ROM monitor mode.

    C. The router will enter global configuration mode.

    D. The boot will hang until an IOS is available.


    参考答案：B

  • 第4题：

    A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?()

    A. The IOS image will be ignored.

    B. The router will prompt to enter initial configuration mode.

    C. The router will boot to ROM.

    D. Any configuration entries in NVRAM will be ignored.

    E. The configuration in flash memory will be booted.


    参考答案：B, D

  • 第5题：

    During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next?（）

    • A、Because of damaged flash memory， the router will fail the POST
    • B、It will attempt to locate the IOS from a TFTP server. If this fails， it will initiate the setup dialog.
    • C、It will attempt to locate the IOS from a TFTP server. If this fails， it will load a limited IOS from ROM
    • D、It will attempt to locate the configuration file from a TFTP server. If this fails， it will initiate the setup dialog.
    • E、It will attempt to locate the configuration file from a TFTP server. If this fails， it will load a limited configuration from ROM

    正确答案:C

  • 第6题：

    What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?（）

    • A、To restart the router.
    • B、To bypass the configuration in Flash.
    • C、To view the password before changes are made.
    • D、To bypass setup configuration mode.
    • E、To access ROM Monitor mode.

    正确答案:E

  • 第7题：

    Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）

    • A、The router will enter setup mode.
    • B、The router will enter ROM monitor mode.
    • C、The router will enter global configuration mode.
    • D、The boot will hang until an IOS is available.

    正确答案:B

  • 第8题：

    What will a router do during startup if a configuration file is not located in NVRAM?（）

    • A、it will search for the configuration file in the locations specified by boot system commands.
    • B、it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.
    • C、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.
    • D、it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.
    • E、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.

    正确答案:C

  • 第9题：

    A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file. Which command will display this information, and what is the configuration register value that should be displayed?（）

    • A、show startup-config and 0x2142
    • B、show version and 0x2102
    • C、show flash and 0x2102
    • D、show version and 0x2142
    • E、show running-config and 0x2142
    • F、show flash and 0x2142

    正确答案:B

  • 第10题：

    多选题
    A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?（）
    A

    The IOS image will be ignored.

    B

    The router will prompt to enter initial configuration mode.

    C

    The router will boot to ROM.

    D

    Any configuration entries in NVRAM will be ignored.

    E

    The configuration in flash memory will be booted.


    正确答案： A,D
    解析： 暂无解析

  • 第11题：

    单选题
    Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）
    A

    The network administrator faled to save the configuration.

    B

    The configuration register is set to 0x2100.

    C

    The boot system flash command is missing from the configuration.

    D

    The configuraiton register is set to 0x2102.

    E

    The router is configured with the boot system startup command.


    正确答案： A
    解析： 暂无解析

  • 第12题：

    单选题
    Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）
    A

    The router will enter setup mode.

    B

    The router will enter ROM monitor mode.

    C

    The router will enter global configuration mode.

    D

    The boot will hang until an IOS is available.


    正确答案： D
    解析： 暂无解析

  • 第13题：

    What will a router do during startup if a configuration file is not located in NVRAM?()

    A. it will search for the configuration file in the locations specified by boot system commands.

    B. it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.

    C. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.

    D. it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.

    E. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.


    参考答案：C

  • 第14题：

    A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with:"Would you like to enter the initial configuration dialog? [yes/no]"Why has this occurred?（）

    A. There is an error in the router DRAM.

    B. Te IOS image is corrupt.

    C. The configuration register is set to 0x2142.

    D. The TFTP server that contains the router configuration file is unreachable.

    E. A boot system configuration command has placed the router into setup mode.


    参考答案：C

  • 第15题：

    After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.What is the most likely cause of this?（）

    A. The NVRAM is corrupted.

    B. The boot system commands were omitted in the configuration.

    C. The configuration register setting is incorrect.

    D. The upgraded configuration incompatible with the hardware platform.

    E. The upgraded IOS incompatible with the hardware.


    参考答案：C

  • 第16题：

    During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next()。

    A.Because of damaged flash memory, the router will fail the POST.

    B.It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.

    C.It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.

    D.It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.

    E.It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.


    参考答案：C

  • 第17题：

    A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）

    • A、There is an error in the router DRAM.
    • B、Te IOS image is corrupt.
    • C、The configuration register is set to 0x2142.
    • D、The TFTP server that contains the router configuration file is unreachable.
    • E、A boot system configuration command has placed the router into setup mode.

    正确答案:C

  • 第18题：

    A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?（）

    • A、The IOS image will be ignored.
    • B、The router will prompt to enter initial configuration mode.
    • C、The router will boot to ROM.
    • D、Any configuration entries in NVRAM will be ignored.
    • E、The configuration in flash memory will be booted.

    正确答案:B,D

  • 第19题：

    You have just purchased a brand new router and wish to have the router prompt you through the initial configuration commands. Which router mode does this describe?（）

    • A、ROM Monitor mode
    • B、SETUP mode
    • C、Autoflash mode
    • D、RXBOOT mode
    • E、None of the above

    正确答案:B

  • 第20题：

    After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）

    • A、The NVRAM is corrupted.
    • B、The boot system commands were omitted in the configuration.
    • C、The configuration register setting is incorrect.
    • D、The upgraded configuration incompatible with the hardware platform.
    • E、The upgraded IOS incompatible with the hardware.

    正确答案:C

  • 第21题：

    单选题
    After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）
    A

    The NVRAM is corrupted.

    B

    The boot system commands were omitted in the configuration.

    C

    The configuration register setting is incorrect.

    D

    The upgraded configuration incompatible with the hardware platform.

    E

    The upgraded IOS incompatible with the hardware.


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    What will a router do during startup if a configuration file is not located in NVRAM?（）
    A

    it will search for the configuration file in the locations specified by boot system commands.

    B

    it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.

    C

    it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.

    D

    it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.

    E

    it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.


    正确答案： E
    解析： 暂无解析

  • 第23题：

    单选题
    During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。
    A

    Because of damaged flash memory, the router will fail the POST.

    B

    It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.

    C

    It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.

    D

    It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.

    E

    It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.


    正确答案： E
    解析： 暂无解析

相关内容