To restart the router.
To bypass the configuration in NVRAM.
To view the lost password.
To save the changes to the configuration.
To enter ROM Monitor mode.
第1题:
A. Reset the root password.
B. Press the space bar.
C. Type recovery.
D. Press the "Enter" key.
第2题:
A. To restart the router.
B. To bypass the configuration in Flash.
C. To view the password before changes are made.
D. To bypass setup configuration mode.
E. To access ROM Monitor mode.
第3题:
用半径为R的圆弧外切连接两个半径分别为R1,R2的圆弧。确定连接圆弧圆心的方法为:分别以两已知圆弧的圆心O1,O2为圆心,以()为半径作圆弧,其交点即为连接弧的圆心O。
第4题:
You are a senior network administrator at TestKing, and while performing thepassword recovery procedure on your 2500 series Cisco router, you type in thefollowing command:o/r 0x2142What is the purpose of this command?()
第5题:
r1 is the hub , multipoint mode subinterface, r2 and r3 is spoke, when r2 down at the spoke, What will r1 react?how about r3?
第6题:
醚可表示为()。
第7题:
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? ()
第8题:
关于制冷系统使用的O形圈,下列说法哪些是正确的()
第9题:
to increase the system efficiency by sensible heat transfer
to stop the liquid from flashing
to reduce the load on the compressor
to remove latent heat of vaporization and the suction piping transfer
第10题:
An exception is thrown at runtime.
r, e, o,
Compilation fails.
r, t, t,
第11题:
Reset the root password
Press the space bar
Type recovery
Press the Enter key
第12题:
It is used to validate the sources of VTP advertisements sent between switches.
It is used to access the VTP server to make changes to the VTP configuration.
It allows two VTP servers to exist in the same domain, each configured with different passwords.
It is the password required when promoting a switch from VTP client mode to VTP server mode.
It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.
第13题:
A. area 0 stub o n routers R4 and R5
B. area 5 stub on routers R4 and R5
C. area 5 stub no - summary on routers R4 and R5
D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5
E. area 5 stub no - summary on router R4 and area 5 stub on router R5
第14题:
第15题:
What is the purpose of the command shown below?vtp password Fl0r1da()
第16题:
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?()
第17题:
下列热力学条件中,有利于脱硫的是()。
第18题:
酯的分子通式可写为()。
第19题:
What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?()
第20题:
It is used to restart the router.
It is used to bypass the configuration in NVRAM.
It is used to enter ROM Monitor mode.
It is used to view the lost password.
It is used to save the changes to the configuration.
第21题:
To restart the router.
To bypass the configuration in NVRAM.
To view the lost password.
To save the changes to the configuration.
To enter ROM Monitor mode.
第22题:
To restart the router.
To bypass the configuration in Flash.
To view the password before changes are made.
To bypass setup configuration mode.
To access ROM Monitor mode.
第23题:
S-see,O-organize,R-respond
S-sense,O-organize,R-react
S-stimulus,O-organism,R-reaction
S-stimulate,O-organize,R-respond
S-sensory,O-organism,R-response
第24题:
Reset the root password.
Press the space bar.
Type recovery.
Press the Enter key.