A. The command is used to establish a static route.
B. The default administrative distance is used.
C. The command is used to configure the default route.
D. The subnet mask for the source address is 255.255.255.0
E. The command is used to establish a stub network
第1题:
Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4 (Choose two.)()。
第2题:
The following configuration command was issued on router TK1:ip route 172.16.3.0 255.255.255.0 192.168.2.1.Which of the following statements are true regarding this command?()
第3题:
Which of the following statements are true concerning the command ip sla monitor responder typetcpconnect ipaddress 10.1.1.1 port 23?(Choose all that apply.)()
第4题:
The command "ip route 192.168.24.64 255.255.255.192 192.168.8.2 100" was configured on a router named TK1. No routing protocols or other static routes are configured on the Corporate router yet.Based on this information, which statement is true about this command?()
第5题:
The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?()
第6题:
Which two statements are true about the command ip route 172.16.3.0 255.255.255.0 192.168.2.4?()
第7题:
Given the following MPLS L2 configuration command: mpls-relay 10.1.1.1 4 Which two statements true? ()(Choose two.)
第8题:
This command sets a gateway of last resort for the TK1 router.
The number 100 indicates the number of hops to the destination network.
The interface with IP address 192.168.8.2 is on the TK1 router.
The command creates a static route for all IP traffic with the source address 192.168.24.64.
Packets destined for host 192.168.24.124 will be sent to 192.168.8.2.
None of the above
第9题:
This command should be executed from the global configuration mode
The IP address 10.121.16.8 is the local router port used to forward data
102 is the remote DLCI that will receive the information
This command is required for all Frame Relay configurations
The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
第10题:
The default administrative distance is used.
The command is used to establish a static route.
The command is used to configure the router interfaces.
The command is used to establish a stub network.
The subnet mask for the source address is 255.255.255.0
第11题:
It establishes a static route to the 172.16.3.0 network.
It establishes a static route to the 192.168.2.0 network.
It configures the router to send any traffic for an unknown destination to the 172.16.3.0 network.
It configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4.
It uses the default administrative distance.
It is a route that would be used last if other routes to the same destination exist.
第12题:
The command is used to establish a static route.
The default administrative distance is used.
The command is used to configure the default route.
The subnet mask for the source address is 255.255.255.0
The command is used to establish a stub network
第13题:
The network administrator of the Oregon router adds the follwing command to the router configuration: ip route 192.168.12.0 255.255.255.0 172.16.12.1. What are the results of adding this command?()
第14题:
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command?()
第15题:
Which three statements are true about EIGRP route summarization?()
第16题:
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output?() B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
第17题:
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?()
第18题:
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command()。
第19题:
This command should be executed from the global configuration mode.
The IP address 10.121.16.8 is the local router port used to forward data.
102 is the remote DLCI that will receive the information.
This command is required for all Frame Relay configurations.
The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
第20题:
It establishes a static route to the 172.16.3.0 network
It establishes a static route to the 192.168.2.0 network
It configures the router to send any traffic for an unknown destination to the 172.16.3.0 network
It configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4
It uses the default administrative distance
It is a route that would be used last if other routes to the same destination exist
第21题:
The command establishes a static route.
The command invokes a dynamic routing protocol for 192.168.12.0.
Traffic for network 192.168.12.0 is forwarded to 172.16.12.1.
Traffic for all networks is forwarded to 172.16.12.1.
This route is automatically propagated throughout the entire network.
Trafficfor network 172.16.12.0 is forwarded to the 192.168.12.0 network.
第22题:
This command is applied to the core router facing interface.
This command is applied to the customer facing interface.
The 4 is locally significant and identifies the layer 2 circuit.
The 4 must match exactly on the peer router configuration on the remote end.
第23题:
The command will initiate a probe with a destination IP address of 10.1.1.1
The command is used on the IP SLA responder and the IP SLA source
The command will allow only source address 10.1.1.1 to source probes
The command will initiate a probe with a destination Telnet port
The command is used to make the router a responder
The command will initiate a probe with a source port of 23
第24题:
It establishes a static route to the 172.16.3.0 network.
It establishes a static route to the 192.168.2.0 network.
It configures the router to send any traffic for an unknown destination to the 172.16.3.0 network.
It configures the router to send any traffic for an unknown destination out the interface with the address 192.168.2.4.
It uses the default administrative distance.
It is a route that would be used last if other routes to the same destination exist.